manualshive.com logo in svg

DataRemote POTS in a BOX CDS-9070, User Manual

Introducing the DataRemote POTS in a BOX CDS-9070 - a powerful communication device designed to streamline your operations. Our comprehensive User Manual, available for free download at manualshive.com, provides detailed instructions on maximizing the potential of this innovative product. Simplify your setup and increase efficiency with this essential manual.

Share
Download
background image

Copyright © 2016 - All rights reserved by DataRemote Incorporated

 

V1.0 

The page 75 of 76 

Revision Time: 2016-10-13 

7 Statement 

FCC 

Interference 

Statement

DataRemote Incorporated. Declares that this device is in compliance with the essential requirements. 

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1) 

This device may not cause harmful interference, and

(2) 

This device must accept any interference received, including interference that may cause

 undesired operation. 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed 

to provide  reasonable  protection  against  harmful  interference  in a residential  installation.  This equipment  generates,  uses  and  can  radiate  radio  frequency 

energy  and,  if  not  installed  and  used  in accordance  with  the  instructions,  many  cause  harmful  interference  to  radio  communications.  However, there  is no 

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which 

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is

 connected.

-

Consult the dealer or an experienced radio/TV technician for help. 

To assure continued compliance, any changes or modifications not expressly approved by the party 

responsible for compliance could void the user’s authority to operate this equipment. (Example- 

use only shielded interface cables when connecting to computer or peripheral devices)

, 

This transmitter must not be co-located or operating in conjunction with any other antenna or 

transmitter. 

Operations in the 5.15-5.25GHz band are restricted to indoor usage only.

Summary of Contents for POTS in a BOX CDS-9070













































































Reviews:

No comments

Related manuals for POTS in a BOX CDS-9070

Digisol DG-BR4313NG User Manual preview
DG-BR4313NG
Brand: Digisol Pages: 142
NETGEAR AirCard 815S User Manual preview
AirCard 815S
Brand: NETGEAR Pages: 98
SMC Networks Barricade SMC7004VWBR V.2 User Manual preview
Barricade SMC7004VWBR V.2
Brand: SMC Networks Pages: 82
Buffalo Tech Nfiniti Airstation WHR-G300N User Manual preview
Nfiniti Airstation WHR-G300N
Brand: Buffalo Tech Pages: 48
NEC Aterm W300P Setup Manual preview
Aterm W300P
Brand: NEC Pages: 4
NEC PA-MR10LN Instruction Manual preview
PA-MR10LN
Brand: NEC Pages: 25
NEC Aterm MR03LN Instruction Manual preview
Aterm MR03LN
Brand: NEC Pages: 25
NEC NAR01 Instruction Manual preview
NAR01
Brand: NEC Pages: 26
NEC UNIVERGE WL Quick Installation Manual preview
UNIVERGE WL
Brand: NEC Pages: 34
NEC OPS-DRD User Manual preview
OPS-DRD
Brand: NEC Pages: 46
NEC NP06LM Important Information Manual preview
NP06LM
Brand: NEC Pages: 48
Wunda Smart Hub Installation Manual preview
Smart Hub
Brand: Wunda Pages: 2
Cyberoam NetGenie Soho Quick Start Manual preview
NetGenie Soho
Brand: Cyberoam Pages: 12
EnGenius EOC-5610 User Manual preview
EOC-5610
Brand: EnGenius Pages: 64
EnGenius ENS620EXT User Manual preview
ENS620EXT
Brand: EnGenius Pages: 71
EnGenius ENH220EXT User Manual preview
ENH220EXT
Brand: EnGenius Pages: 67
EnGenius ENH200EXT User Manual preview
ENH200EXT
Brand: EnGenius Pages: 86
EnGenius ENH200 User Manual preview
ENH200
Brand: EnGenius Pages: 100

Brands by name

Popular brands

Load more brands