DataRemote POTS in a BOX CDS-9070 User Manual Download Page 52

Page: 52 / 76

V1.0

The page 52 of 76

Revision Time: 2016-10-13

WPS Config

If or not enable WPS.

WPS Summary

The status for Current connection,

SSID and so on

WPS Progress

PIN: In the following PIN options, fill

in the PIN code of the client (wireless

card, etc.) that needs to be accessed,

and then click Apply.

PBC: PBC mode There are two ways

to start, you can directly press the PBC

button on the hardware, or select to

PBC mode, and then click Apply.

WPS Status

There are three WPS states:

WSC: Idle state is idle

WSC: Start WSC Process Status is to

start sending messages

WSC: Success: If a client accesses an

AP, the WPS connection succeeds

Summary of Contents for POTS in a BOX CDS-9070











































































Search results

Summary of Contents for POTS in a BOX CDS-9070

Reviews:

Related manuals for POTS in a BOX CDS-9070

Brands by name

Popular brands

DataRemote POTS in a BOX CDS-9070, User Manual

Search results

Summary of Contents for POTS in a BOX CDS-9070

Reviews:

Related manuals for POTS in a BOX CDS-9070

Brands by name

Popular brands