Datalogic S70 Quick Start Manual Download Page 9

 

 

TECHNICAL DATA

 

 

 

 
 

Sensing Beam: 

Visible red, 635 nm 

Supply Voltage: 

Voltage output models: 

12 to 30 VDC Class 2 (10% maximum ripple) 

Current output models: 

10 to 30 VDC Class 2 (10% maximum ripple) 

Power and Current Consumption 
(exclusive of load): 

Standard display mode: 

840 mW, Current consumption < 35 mA at 24 VDC 

ECO display mode: 

672 mW, Current consumption < 28 mA at 24 VDC

 

Supply Protection Circuitry: 

Protected against reverse polarity, overvoltage, and transient voltages

 

Delay at Power Up: 

500 milliseconds max.; outputs do not conduct during this time 

Output Configuration: 

Voltage Output Models: 

1 analogue voltage output (user configurable as 1 to 5 V or 0 to 10 V) 

 

with 1 current sinking (NPN) or 1 current sourcing (PNP) 

 

discrete output, depending on model. 

Current Output Models: 

1 analogue current output (4 to 20 mA) with 1 current sinking (NPN) 

 

or 1 current sourcing (PNP) discrete output, depending on model 

Discrete Output Rating: 

100 mA maximum combined load—analogue plus discrete outputs 
(derate 1 mA per °C above 30 °C) 

OFF-state leakage current: 

< 5 

ȝ

A at 30 VDC; 

ON-state saturation voltage: NPN: 

< 1.5 V; 

PNP : 

< 2 V 

Analogue Output Recovery Time: 

< 2× the selected response speed 

Analogue Output Ripple Content (p-
p): 

< 0.5% of the full scale analogue output 

Analogue Output Rating: 

Voltage Outputs: 

2.5 kOhm minimum load resistance 

Current Outputs: 

1 kOhm maximum load resistance at 24 V; 

 

maximum load resistance = [(Vcc - 4)/.02] Ohms 

Output Protection: 

Protected against output short-circuit, continuous overload,  
transient over-voltages, and false pulse on power up 

Construction: 

Black ABS / Polycarbonate alloy (UL94 V-0 rated) 
housing, clear polycarbonate cover 

Environmental Rating: 

IEC IP50, NEMA 1 

Operating Temperature: 

í

10 °C … +55 °C 

Storage Temperature: 

í

20 °C… +85 °C 

Humidity: 

50% at +50 °C maximum relative humidity (non- condensing) 

Connections: 

4-pin M8 connector 

 
 

Response Speed and Features

 

Description

 

Response 

Speed

 

Repetition Period

 

Repeatability

 

Cross-Talk 

Avoidance

 

Energy 

Efficient Light 

Resistance

 

Maximum 

Range

 

High Speed 

250 

μ

s 50 

μ

s 50 

μ

s No  No 

900 

mm 

Fast 500 

μ

s 50 

μ

s 75 

μ

s Yes  No 

1125 

mm 

Standard 1 

ms 

50 

μ

s 90 

μ

s Yes Yes 

1125 

mm 

Long Range 

4 ms 

50 

μ

s 90 

μ

s Yes Yes 

1462.5 

mm 

Extra Long Range 

12 ms 

50 

μ

s 90 

μ

s Yes Yes 

2250 

mm 

 

NOTE:  These values are valid for opposed mode sensing using a 1 mm diameter core plastic fiber. 

 
 

Summary of Contents for S70











Reviews: