DataDirect Networks EF3015 Setup Manual Download

Page: 45 / 59

LED Descriptions

E F 3 0 1 5 S e t u p G u i d e ( R e v A )

A.2

Disk Drive LEDs

3.5” LFF Disk Drive

2.5” SFF Disk Drive

LFF Disk Drive LEDs

LED No./Description

Color

State

Definition

1— OK to Remove

Blue

The drive module has been removed from any active
virtual disk, spun down, and prepared for removal.

Off

The disk drive module is not prepared for removal.

2— Power/Activity/Fault

Green

The disk drive module is operating normally.

Blink

The disk drive module is initializing; active and
processing I/O; is performing a media scan; or the vdisk
is initializing or rebuilding.

Off

If neither green nor amber, the disk drive module is not
powered on.

Amber

The disk has failed; experienced a fault; is a leftover; or
the vdisk is down or critical.

Blink

Physically identifies the drive module.

Off

If neither green nor amber, the disk drive module is not
powered on.

SFF Disk Drive LEDs

LED No./Description

Color

State

Definition

1— Power/Activity

Green

The disk drive module is operating normally.

Blink

The disk drive module is initializing; active and
processing I/O; is performing a media scan; or the vdisk
is initializing or rebuilding.

Off

If neither green nor amber, the disk drive module is not
powered on.

2— Fault

Amber

The disk has failed; experienced a fault; is a leftover; or
the vdisk is down or critical.

Blink

Physically identifies the drive module.

Off

If neither green nor amber, the disk drive module is not
powered on.

Summary of Contents for EF3015




























































Search results

Summary of Contents for EF3015

Reviews:

Related manuals for EF3015

Brands by name

Popular brands

DataDirect Networks EF3015, Setup Manual

Search results

Summary of Contents for EF3015

Reviews:

Related manuals for EF3015

Brands by name

Popular brands