Datacom Systems VS-1200 Series User Manual Download Page 11

Page: 11 / 54

Overview

2.4

VS-1200 Series Common Specifications

Management Port (front):

RJ45 @ 100 Mbps Full-Duplex

The factory configured IP Address, Subnet Mask and Default Gateway are as follows:

IP Address:

192.168.1.1;

Subnet Mask:

255.255.255.0;

Default Gateway:

0.0.0.0

Serial Port (rear):

DB9

Power Requirement:

Two external power adapters

Input

: 100 - 240VAC 50 - 60Hz, 0.4-0.2 A —

Output

: 5VDC, 2.5A

Certified : CE, UL, CUL, CSA, TUV, CCC, PSE, JET, EU RoHS and China RoHS

Power Consumption:

12W;

BTU/h:

40.9

Operating Temperature:

32º to 104° F — 0º to 40° C

Storage Temperature: -

22º to 149° F — -30º to 65° C

Operating Range Relative Humidity:

5 to 90% non-condensing

Dimensions (H x W x D):

includes RMC-2 rack mount bracket

1.750 x 7.950 x 7.775 inch
4.44 x 20.19 x 19.75 cm

Weight:

1.5 lbs; shipping: 6.5 lbs — 0.68 kg; shipping; 2.95 kg

Warranty:

Two (2) years - see '

Warranty'

section for details.

2.5

VS-1200 Series Model Specific Specifications

VS-1204BT:

Any-to-Any Ports: 4 - 10/100/1000BaseT (RJ45 Connectors)

VS-1204SFP:

Any-to-Any Ports: 4 - SFP*

VS-1206SFP:

Any-to-Any Ports: 6 - SFP*

VS-1208BT:

Any-to-Any Ports: 8 - 10/100/1000BaseT (RJ45 Connectors)

VS-1210BT/SFP:

Any-to-Any Ports: 8 - 10/100/1000BaseT (RJ45 Connectors), 2 - SFP*

VS-1210SFP:

Any-to-Any Ports: 10 - SFP*

*SFP = Small Form Pluggable can be LX, SX or 1000Mbs copper

(Support Datacom supplied only)

Summary of Contents for VS-1200 Series























































Search results

Summary of Contents for VS-1200 Series

Reviews:

Related manuals for VS-1200 Series

Brands by name

Popular brands

Datacom Systems VS-1200 Series, User Manual

Search results

Summary of Contents for VS-1200 Series

Reviews:

Related manuals for VS-1200 Series

Brands by name

Popular brands