background image

Data Industrial 

Series 340LW Owner’s 

Manual

13

W a r r a n t y

Data Industrial Corporation (“Seller”) of 11 Industrial Drive, Mattapoisett, Massachusetts 02739-0740, U.S.A.,
warrants to the original purchaser of its product that such product manufactured by Data Industrial Corpora-
tion shall be free from defects in materials or workmanship when installed, serviced and operated according to
Data Industrial Corporation instructions or in other such normal use. This warranty is effective for a period of
12 months from the date of installation by the Purchaser or 18 months from the date of shipment by the “Seller”
whichever occurs or terminates first. This limited warranty does not cover damage or loss resulting from
corrosion or erosion caused by acids or other chemicals or by severe environmental conditions or negligent or
improper installation or improper operation, misuse, accident, unauthorized repair or substitution of compo-
nents other than those provided by the “Seller”, and does not cover limited life components such as bearings,
shafts, impellers where wear rate is a function of application and environment.  Any component not manufac-
tured by the “Seller” but included in its products shall not be covered by this warranty and is sold only under
such warranty as the manufacturer may provide.

If Buyer or Purchaser wishes to make a claim hereunder, he shall send written notice of any defect within the
warranty period, to “Seller” at the above address.  “Seller” may at its sole option instruct Buyer to ship subject
part, postage prepaid, to the “Seller” at above address or authorize a representative to inspect the part on site.
“Seller” will at its sole option repair or replace any defective product covered by this warranty.  If Buyer makes
repairs or alterations to any product or part covered by this warranty without “Sellers” prior written approval,
this warranty shall be null and void.

The foregoing shall constitute Buyers or Purchasers sole and exclusive remedy against “Seller”, and no other
remedy, including but not limited to, incidental or consequential damages for personal injury, loss of fluids,
gases or other substances or for loss of profits or injury to property or person shall be available to the Buyer or
Purchaser.  The warranty extended herein shall be in lieu of any other implied warranty of merchantability or
fitness for a particular purpose, and seller shall bear no liability for representatives or retail sellers.  In no event
shall Data Industrial Corporation be liable for any contingent, incidental, or consequential damage or ex-
penses due to partial or complete inoperability of its product.

All rights reserved.  No part of this work covered by the copyrights hereon may be reproduced or copied in
any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping, or
information and retrieval systems -- without written permission of Data Industrial.

Copyright © 2002
Data Industrial Corporation
11 Industrial Drive
Mattapoisett, MA  02739
TEL: 508-758-6390
FAX: 508-758-4057
email:

[email protected]
[email protected]

web site: www.dataindustrial.com

Summary of Contents for 340LW Series














Reviews: