background image

P

AGE

 12

44443-1098 <90-00059>

FCC REQUIRED INFORMATION

T

he following are requirements of Part 68 of FCC Rules:

1.

The installer of this equipment is responsible for notifying the tele-

phone company that it is being connected or disconnected.

2.

This equipment is not to be connected to party lines or coin tele-

phone service.

3.

The telephone company has the right to temporarily discontinue

service (Section 68.108) and to change facilities and services which

may affect the operation of this equipment. Adequate written no-

tice will be provided to the user to maintain uninterrupted service

(Section 68.110B).

4.

In case of trouble, contact the manufacturer’s authorized agent.

5.

When the installation of this device requires connection or changes

to the internal wiring of registered telephones or other registered

devices, such changes and connections can be made only by the

registered grantee or authorized agents, equipment manufacturers,

registered telephone refurbishers, telephone companies, and those

qualified for the installation of KN and PN systems under Section

68.215 of the rules. The installer of this equipment is advised, in

the interest of safety, that the host equipment be disconnected from

all power sources and the telephone network when the installation

is being made.

6.

Installation of this equipment as an adjunct can be made only with

permission of the owner of the host equipment.
FCC required information pertaining to this module:
Registration Number:

 DPH62Z-14478-WP-T

Summary of Contents for 44443















Reviews: