manualshive.com logo in svg

DANPHONE Futronic MKII, User Manual

Share
Download
DANPHONE Futronic MKII User Manual Download Page 7

 

Page 7 of 65 

 

 

ACCESSORIES 

 
The test box comes with the following standard accessories: 
 
1 pcs 

Power adapter 100-240 VAC / 13,2 VDC 

1   - 

Cable for external DC power 
incl. Cigar lighter plug 

1   - 

USB cable for connection to PC 

1   - 

Coax cable, 25 cm, with BNC 

 

2   - 

Coax cable, 150 cm, with BNC 

 

1   - 

Coax cable, 500 cm, with BNC 

1   - 

AIS signal combiner / dummy load  

1   - 

Audio Reference / AF Generator   

1   - 

Telescopic antenna for VHF/AIS   

1   - 

Wire antenna for MF/HF/NAVTEX   

2   - 

UHF plug to BNC socket adapter   

1   - 

UHF socket to BNC socket adapter 

 

1   - 

BNC socket to BNC socket adapter 

 

1   - 

User’s Manual in English 

 

1   - 

Calibration Certificate 

 

 
OPTIONAL ACCESSORIES 

 

RF Amplifier 

If the test box signal is not powerful enough when testing NAVTEX receivers and MF radios 
over the air, adding this RF amplifier will increase the output level by 15-20 dB. 
 

Watertight and Crush Proof Case 

This case is specially configured to hold the tester and accessories safe and secure. Weight 
only 3.9 kgs. External dimensions: 460 x 360 x 175 mm. 
 

Backpack with protective cases 

The waterproof backpack protects the test box and all accessories. It contains two 
cases made of Polyethylene Foam to support and secure the equipment. The backpack 
is ergonomic for back and shoulders and is easy and handy for transportation. 
 

Set of Attenuators 

Attenuators are used e.g. with AIS tests and VHF sensitivity tests. The set includes 1x10 dB, 
1x20 dB and 1x40 dB attenuators, 2 Watt, with BNC. 

 
Pilot Plug Cable

 

This cable is used with the testing of pilot plugs onboard ships. The cable is equipped with a 
jack to fit standard pilot plugs. 
 

MF/HF Power Sensor 

 

This unit is used to measure the power extracted from the MF/HF radio on frequency 2MHz to 
25.2MHz. The max. power is 500W PEP 2 min. Continuous 250W PEP.   
 

Summary of Contents for Futronic MKII


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands