manualshive.com logo in svg

DANPHONE Futronic MKII, User Manual

Share
Download
DANPHONE Futronic MKII User Manual Download Page 35

 

Page 35 of 65 

 

 

 
 
Use this setup to perform the MH/HF power test.  
 
 

 
 
 
 
 
 
 
 
 
 
 

Select 

“MF/HF Radios”

 and set number. Select 

“MF/HF power test”

 and choose MF/HF band 

by pressing ↑ or

 

↓

 to scroll up and down. Press 

“OK”

 to confirm.  

 

 

 

Use Audio Reference for modulation with dual tone for measuring.  
 
Then, activate the transmitter and keep it activated while selecting 

“Meas”. 

 
In the Meas (= measure) mode, the test box will perform and display a single 
power measurement and store it in the test box memory. 
 
In the Cont (= continuous) mode, the test box will continue taking measurements until pressing 
the EXIT button. Cont readings are not stored, but the feature can be used e.g. for 
checking/adjusting the antenna.  
 
 
 

 

Example of Printout from the Memory: 

 

 

MF/HF # 1   Time/date: 08:48:28 / 04-12-2019 
RF range: 25.0 - 25.2 MHz  Fwd: 264 Watt PEP  Rev: 1 Watt PEP VSWR: 1.1 
 
MF/HF # 1   Time/date: 08:49:06 / 04-12-2019 
RF range: 6.0 - 6.3 MHz  Fwd: 261 Watt PEP  Rev:  0 Watt PEP  VSWR:  1.0 
 

 
 
 
 
 
 
 
 
 
 

 

ANT. 

Danphone’s Audio reference 

MF/HF TRANSMITTER 

ATU 

Summary of Contents for Futronic MKII


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands