manualshive.com logo in svg

Danfoss VLTAutomationDrive FC 360, Quick Manual

Share
Download
Danfoss VLTAutomationDrive FC 360 Quick Manual Download Page 50

Power

Connections....................................................................................... 13

Factor.................................................................................................... 14

Power-dependent................................................................................ 36
Programming........................................................................................... 7
Protection And Features.................................................................... 41
Pulse Inputs............................................................................................ 39

Q

Quick Menu............................................................................................. 20

R

RCD............................................................................................................ 14
Reference.................................................................................................. iii
Relay Outputs........................................................................................ 40
Remote Commands............................................................................... 9
Reset................................................................................................... 31, 41
RFI Filter................................................................................................... 14

S

Screened Control Cables................................................................... 16
Serial Communication...................................................... 9, 16, 31, 17
Shielded Cable....................................................................................... 13
Specifications........................................................................... 10, 17, 36
Speed Reference................................................................................... 28
Start Up.................................................................................................... 34
Supply Voltage...................................................................................... 39
Surroundings......................................................................................... 41
Symbols..................................................................................................... iii
System Feedback.................................................................................... 9

T

Technical Data....................................................................................... 38
Terminal Programming...................................................................... 16
Thermistor............................................................................................... 30
Tightening Of Terminals.................................................................... 44
Torque Characteristics........................................................................ 38
Trip Function.......................................................................................... 13
Troubleshooting................................................................................... 34

V

Voltage Level.......................................................................................... 38

W

Warnings And Alarms.................................................................. 32, 33
Wire Sizes................................................................................................. 13
Wiring Examples................................................................................... 28

Index

VLT

®

 AutomationDrive FC 360 Quick Guide

46

MG06A102 - VLT

®

 is a registered Danfoss trademark

Summary of Contents for VLTAutomationDrive FC 360





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands