manualshive.com logo in svg

Danfoss VLTAutomationDrive FC 360, Quick Manual

Share
Download
Danfoss VLTAutomationDrive FC 360 Quick Manual Download Page 27

Array parameters function as follows:

130BC448.10

1

2

4

5

6

7

8

9

10

OK

Back

Back

Back

5 x

Setup 1

Setup 1

Setup 1

Setup 1

%

INDEX

%

INDEX

%

INDEX

Setup 1

INDEX

%

OK

OK

OK

Illustration 4.7 Main Menu Interactions - Array Parameters

1

[OK]: shows parameter numbers and the value in the first
index.

2

[OK]: Index can be selected.

3

[

▲

][

▼

]: Selects index.

4

[OK]: Value can be edited.

5

[

▲

][

▼

]: changes parameter value (flashing).

6

[Back]: cancel changes
[OK]: accept changes

7

[Back]: cancels editing index, a new parameter can be
selected.

8

[

▲

][

▼

]: selects parameter within the group.

9

[Back]: removes parameter index value and shows the
parameter group.

10 [

▲

][

▼

]: selects group.

Table 4.6

4.4  Parameter List

User Interface and Programm...

VLT

®

 AutomationDrive FC 360 Quick Guide

MG06A102 - VLT

®

 is a registered Danfoss trademark

23

4

4

Summary of Contents for VLTAutomationDrive FC 360





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands