manualshive.com logo in svg

Danfoss VLTAutomationDrive FC 360, Quick Manual

Share
Download
Danfoss VLTAutomationDrive FC 360 Quick Manual Download Page 23

D. Operation keys and indicator lights (LEDs)

13 [Hand On]: Starts the motor and enables control of the

frequency converter via the LCP.

NOTE

Terminal 27 Digital Input (

5-12 Terminal 27 Digital

Input

) has coast inverse as default setting. This

means that [Hand On] will not start the motor if
there is no 24 V to terminal 27.

14 [Off/Reset]: stops the motor (off). If in alarm mode the

alarm will be reset.

15 [Auto On]: frequency converter is controlled either via

control terminals or serial communication.

Table 4.3

4.1.3 The Right-Key Function

WARNING

The [Off/Reset] key is not a safety switch. It does not
disconnect the frequency converter from mains.

[

►

] makes it possible to edit any of the four digits on the

display individually. When pressing [

►

] once the cursor

moves to the first digit and the digit starts flashing as
shown in 

Illustration 4.3

. The value can now be changed

using the [

▲

] [

▼

] navigation keys. Pressing [

►

] will not

change the value of the digits or move the decimal point.

130BC440.10

Setup 1

Setup 1

Setup 1

Setup 1

Setup 1

Illustration 4.3 Right Key Function

The right key can also be used for moving between
parameter groups: when in main menu, press the right key
to move to the first parameter in the next parameter
group (e.g. move from 0-03 [0] to 1-00 [0]).

User Interface and Programm...

VLT

®

 AutomationDrive FC 360 Quick Guide

MG06A102 - VLT

®

 is a registered Danfoss trademark

19

4

4

Summary of Contents for VLTAutomationDrive FC 360





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands