manualshive.com logo in svg

Danfoss VLT Soft Starter MCD 600, Installation Manual, Page: 17 / 34

Share
Download
Danfoss VLT Soft Starter MCD 600 Installation Manual Download Page 17

6 Operation

6.1 Requirements for Successful Operation

The EtherNet/IP Card is conformance tested to ODVA. For successful operation, the scanner must also support all functions and
interfaces described in this manual.

N O T I C E

The available features and parameter details may vary according to the model and software version of the soft starter. Refer to
the VLT® Soft Starter MCD 600 Operating Guide for details of parameters and supported features.

6.2 Device Classification

The EtherNet/IP Card is an I/O adapter and must be managed by an I/O scanner over Ethernet.
The EtherNet/IP Card supports both implicit (cyclic) and explicit (acyclic) messaging.

6.3 Ensuring Safe and Successful Control

Data written to the device remains in its registers until the data is overwritten or the device is reinitialized. If the soft starter is con-
trolled via 

parameter 7-1 Command Override

 or is disabled via the reset input (terminals RESET, COM+), fieldbus commands should

be cleared from the registers. If a command is not cleared, it is re-sent to the soft starter once fieldbus control resumes.

6.4 Feedback LEDs

Port 1

Port 2

Keypad

LINK 2

TX/RX2

LINK    1

TX/RX1

ERROR

STATUS

e7

7h

a7

42

.1

0

Table 3: LED Descriptions

LED name

LED state

Description

Error

Off

The device is not powered up or has received an IP address.

Flashing

Connection timeout.

On

Duplicate IP address.

Status

Off

The device is not powered up or has received an IP address.

Flashing

The device has obtained an IP address but has not established any network connections.

On

Communication has been established.

Link x

Off

No network connection.

On

Connected to a network.

TX/RX x

Flashing

Transmitting or receiving data.

AN353423548483en-000101 / 130R0945 | 17

Danfoss A/S © 2020.12

Operation

EtherNet/IP Card

Installation Guide

Summary of Contents for VLT Soft Starter MCD 600



































Reviews:

No comments