Danfoss VLT HVAC Drive FC 102, Programming Manual, Page: 23 / 250

Q3-40 Fan functions Q3-41 Pump functions Q3-42 Compressor functions
Parameter 22-60 Broken Belt Function Parameter 22-20 Low Power Auto Set-up Parameter 1-03 Torque Characteristics
Parameter 22-61 Broken Belt Torque Parameter 22-21 Low Power Detection Parameter 1-71 Start Delay
Parameter 22-62 Broken Belt Delay Parameter 22-22 Low Speed Detection Parameter 22-75 Short Cycle Protection
Parameter 4-64 Semi-Auto Bypass Set-up Parameter 22-23 No-Flow Function Parameter 22-76 Interval between Starts
Parameter 1-03 Torque Characteristics Parameter 22-24 No-Flow Delay Parameter 22-77 Minimum Run Time
Parameter 22-22 Low Speed Detection Parameter 22-40 Minimum Run Time Parameter 5-01 Terminal 27 Mode
Parameter 22-23 No-Flow Function Parameter 22-41 Minimum Sleep Time Parameter 5-02 Terminal 29 Mode
Parameter 22-24 No-Flow Delay Parameter 22-42 Wake-up Speed [RPM] 5-12 Terminal 27 Digital Input
Parameter 22-40 Minimum Run Time Parameter 22-43 Wake-up Speed [Hz] Parameter 5-13 Terminal 29 Digital Input
Parameter 22-41 Minimum Sleep Time Parameter 22-44 Wake-up Ref./FB Difference Parameter 5-40 Function Relay
Parameter 22-42 Wake-up Speed [RPM] Parameter 22-45 Setpoint Boost Parameter 1-73 Flying Start
Parameter 22-43 Wake-up Speed [Hz] Parameter 22-46 Maximum Boost Time Parameter 1-86 Trip Speed Low [RPM]
Parameter 22-44 Wake-up Ref./FB Difference Parameter 22-26 Dry Pump Function Parameter 1-87 Trip Speed Low [Hz]
Parameter 22-45 Setpoint Boost Parameter 22-27 Dry Pump Delay –
Parameter 22-46 Maximum Boost Time Parameter 22-80 Flow Compensation –
Parameter 2-10 Brake Function Parameter 22-81 Square-linear Curve Approxi-
mation –
2-16 AC brake Max. Current Parameter 22-82 Work Point Calculation –
Parameter 2-17 Over-voltage Control Parameter 22-83 Speed at No-Flow [RPM] –
Parameter 1-73 Flying Start Parameter 22-84 Speed at No-Flow [Hz] –
Parameter 1-71 Start Delay Parameter 22-85 Speed at Design Point [RPM] –
Parameter 1-80 Function at Stop Parameter 22-86 Speed at Design Point [Hz] –
Parameter 2-00 DC Hold/Preheat Current Parameter 22-87 Pressure at No-Flow Speed –
Parameter 4-10 Motor Speed Direction Parameter 22-88 Pressure at Rated Speed –
– Parameter 22-89 Flow at Design Point –
– Parameter 22-90 Flow at Rated Speed –
– Parameter 1-03 Torque Characteristics –
– Parameter 1-73 Flying Start –
Table 2.5 Q3-4 Application Settings
2.1.7 Main Menu Mode
Press [Main Menu] to Select the Main Menu mode. The
below read out appears on the display.
The middle and bottom sections on the display show a list
of parameter groups which can be selected by toggling
the [
▲
] and [
▼
] keys.
130BP066.10
1107 RPM
0 - ** Operation/Display
1 - ** Load/Motor
2 - ** Brakes
3 - ** Reference / Ramps
3.84 A 1 (1)
Main Menu
Illustration 2.27 Main Menu Mode
Each parameter has a name and number which remain the
same regardless of the programming mode. In the
Main
Menu mode, the parameters are divided into groups. The
first digit of the parameter number (from the left) indicates
the parameter group number.
All parameters can be changed in the Main Menu.
However, depending on the configuration
(
parameter 1-00 Configuration Mode ), some parameters can
be hidden.
How to Programme Programming Guide
MG11CE02 Danfoss A/S © 03/2015 All rights reserved. 21
2 2