Danfoss VLT AQUA Drive FC 202, Programming Manual

Page: 31 / 294

0-11 Programming Set-up
Option: Function:
Select the set-up to be edited (that is
programmed) during operation; either the
active set-up or 1 of the inactive set-ups. The
set-up number being edited is shown in the
LCP in brackets.
[0] Factory
setup Cannot be edited, but it is useful as a data
source to return the other set-ups to a known
state.
[1] Set-up 1 [1] Set-up 1 to [4] Set-up 4 can be edited freely
during operation, independently of the active
set-up.
[2] Set-up 2
[3] Set-up 3
[4] Set-up 4
[9]
*
Active Set-
up The set-up in which the frequency converter is
operating can be edited during operation.
Editing parameters in the selected set-up
would normally be done from the LCP, but it is
also possible from any of the serial communi-
cation ports.
0-12 This Set-up Linked to
Option: Function:
Use this parameter only if a change of set-ups
is required while the motor is running. This
parameter ensures that parameters which are
not changeable during operation have the
same setting in all relevant set-ups.
To enable conflict-free changes from 1 set-up to
another while the frequency converter is
running, link set-ups containing parameters
which are not changeable during operation.
The link ensures synchronizing of the
not
changeable during operation parameter values
when moving from 1 set-up to another during
operation. Parameters marked with FALSE in the
parameter lists (in
chapter 4 Parameter Lists )
cannot be changed while the frequency
converter is running.
The parameter 0-12 This Set-up Linked to feature
is used when [9] Multi set-up in
parameter 0-10 Active Set-up is selected. Use [9]
Multi set-up to move from 1 set-up to another
during operation while the motor is running.
For example:
Use
[9] Multi set-up to shift from set-up 1 to set-
up 2 while the motor is running. Program
parameters in set-up 1 first, then ensure that
set-up 1 and set-up 2 are synchronized (or
linked).
Synchronization can be performed in 2 ways:
0-12 This Set-up Linked to
Option: Function:
•
Change the edit set-up to [2] Set-up 2
in parameter 0-11 Programming Set-up
and set parameter 0-12 This Set-up
Linked to to [1] Set-up 1 . This starts the
linking (synchronizing) process.
130BP075.10
0-12 This Set-up Linked to
0 RPM 0.00A 1(1)
Set-up Handling
0-1*
[1] Setup 1
Illustration 3.1 Set-up Handling
•
While still in set-up 1, using
parameter 0-50 LCP Copy , copy set-up
1 to set-up 2. Then set
parameter 0-12 This Set-up Linked to to
[2] Set-up 2 . This starts the linking
process.
130BP076.10
0-12 This Set-up Linked to
0 RPM 0.00A 1(1)
Set-up Handling
0-1*
[2] Setup 2
Illustration 3.2 Set-up Handling
After the link is complete,
parameter 0-13 Readout: Linked Set-ups reads
set-ups 1 and 2 to indicate that all not
changeable during operation parameters are now
the same in set-up 1 and set-up 2. If there are
changes to a
not changeable during operation
parameter in set-up 2, for example
parameter 1-30 Stator Resistance (Rs) , they are
also changed automatically in set-up 1. A
switch between set-up 1 and set-up 2 during
operation is now possible.
[0]
*
Not linked
[1] Set-up 1
[2] Set-up 2
[3] Set-up 3
[4] Set-up 4
Parameter Description Programming Guide
MG20OB02 Danfoss A/S © 05/2018 All rights reserved. 29
3 3