manualshive.com logo in svg

Danfoss VLT 5000 Series, Installation Startup Check List, Page: 45 / 45

Share
Download
Danfoss VLT 5000 Series Installation Startup Check List Download Page 45

45

Wiring

• Serial Communications

– Need repeater (amplifier) after 31 drives attached together

– Dip switch settings 2 & 3 to OFF except for 2 bus ends

Serial Communications

This diagram shows how the serial communications is wired.  Notice that it is an RS-

485 connection, which means that all the positive terminals (68) are wired together and all 
the negatives (69) are wired together.  These connections must be in a “Daisy Chain” 
fashion which only has 2 ends.  Star configurations should NOT be used.  The address for 
each drive is set in parameter 500, from address 1 to 126.  The default address is #1.  If 
more than 31 drives are attached a repeater should be used to amplify the signal.

On the control card just above the serial communications plug, there is a DIP switch, 

which is used to enable/disable the EOL (end of line) resistor.  If one or 2 drives are attached 
together, leave the DIP alone.  Once a 3

rd

drive is added, the middle drive must have 

switches 2 and 3 turned OFF, down, to remove the EOL resistor.  If other drives are added, 
all drive that are not on the 2 ends must have DIP switch settings 2 and 3 turned OFF.

Summary of Contents for VLT 5000 Series














































Reviews:

No comments