background image

VLT® 5000/ 5000 FLUX/ 6000 HVAC/
8000 AQUA PROFIBUS

Bit 04, ON 2/OFF 2

In the case of bit 04 = "0", bit 01 of the

Control word is "1"

In the case of bit 04 = "1", bit 01 of the

Control word is "0".

Bit 05, ON 3/OFF 3

In the case of bit 05 = "0", bit 02 of the

Control word is "1"

In the case of bit 05 = "1", bit 02 of the

Control word is "0".

Bit 06, Start possible/Start not possible

Bit 06 is always "0" if FC Drive has been selected

in parameter 512. If Profidrive has been selected in

parameter 512, bit 06 will be "1" after a switch-off

acknowledgement, after activation of OFF2 or OFF3,

and after switching on the mains voltage. Start not

possible will be reset, with bit 00 of the Control word

being set to "0" and bit 01, 02 and 10 being set to "1".

Bit 07, No warning/Warning

In the case of bit 07 = "0", no unusual situation exists.

In the case of bit 07 = "1", an unusual status of

the frequency converter has occurred. All warnings

are described in the operations manual.

Bit 08, Speed

reference / Speed = reference:

In the case of bit 08 = "0", the current speed of the

motor deviates from the set speed reference value.

This may occur, for example, when the speed is being

changed during start/stop through ramp up/down.

In the case of bit 08 = "1", the current speed of the

motor corresponds to the set speed reference value.

Bit 09, Local operation/Bus control

Bit 09 = "0" indicates that the frequency converter has

been stopped by means of the stop switch of the control

panel, or that Local has been selected in parameter 002.

In the case of bit 09 = "1", the frequency converter

can be controlled through the serial interface.

Bit 10, Not in operating range/Frequency limit OK

In the case of bit 10 = "0", the output frequency is

outside the limits set in parameter 225 and parameter

226 (Warnings: frequency low or frequency high).

In the case of bit 10 = "1", the output frequency

is within the indicated limits.

Bit 11, No operation/Operation

In the case of bit 11 = "0", the motor does not turn.

In the case of bit 11 = "1", the frequency converter has a

start signal, or the output frequency is higher than 0 Hz.

Bit 12, VLT OK/Stopped, autostart

In the case of bit 12 = "0", there is no temporary

overloading of the inverter.

In the case of bit 12 = "1", the inverter has stopped

due to overloading. However, the frequency

converter has not switched off (trip) and will start

again after the overloading has ended.

Bit 13, Voltage OK/Limit exceeded

In the case of bit 13 = "0", the voltage limits of the

frequency converter are not exceeded.

In the case of bit 13 = "1", the direct voltage

in the intermediate circuit of the frequency

converter is too low or too high.

Bit 14, Moment OK/Limit exceeded

In the case of bit 14 = "0", the motor current is below

the moment limit selected in parameter 221.

In the case of bit 14 = "1", the moment limit selected

in parameter 221 is exceeded.

Bit 15, Timer OK/Limit exceeded

In the case of bit 15 = "0", the timers for the thermal

motor protection and thermal frequency converter

protection have not exceeded 100%. In the case of bit

15 = "1", one of the timers has exceeded 100%.

MG.90.G1.02 - VLT is a registered Danfoss trademark

26

Summary of Contents for VLT 5000 Series
































































Reviews: