background image

Horn control

The joystick provides a button for activating the vehicle’s horn. The button drives an external relay by
switching a provided voltage. This design allows using the horn even when the joystick itself is not
powered.

Force feedback

Active Force Feedback is an essential comfort function in JS1-H Steer by Wire. The Force Feedback
components enable emulating the physical haptics of steering a vehicle, even though there is no
mechanical connecting between the wheels and the joystick.

Monitor direction of the Force Feedback function is considered safety-relevant to prevent the motor shaft
from moving more than a defined amount in an unintended direction.

Operator notification

The operator notification consists of a buzzer tone and a vibration feedback. This is part of the
redundancy concept since the joystick is designed to reliably inform the operator about errors in the
steering system.

Vibration- and buzzer patterns are not configurable, as the following diagram shows.

OPN-Pattern-Buzzer

OPN-Pattern-Vibrate

Vibration Feedback

Buzzer Signal

Pattern Period

1000ms

400ms

Pattern on Time

500ms

200ms

OPN Period

5000ms

1000ms

OPN On Time

2000ms

2000ms

Mechanical characteristics

Joystick grip

Maximum sideways load

900 N (100mm above the rotation point)

Maximum horizontal load

750 N (100mm above the rotation point)

Maximum vertical load

1000 N (applied straight down on the grip)

User and Safety Manual

PLUS+1® JS1-H Steer by Wire

Steer by Wire Joystick

 

©

 Danfoss | December 2022

AX436683569858en-000101 | 9

Summary of Contents for PLUS+1 JS1-H


























Reviews: