background image

The certification is not a guarantee for that the realized functional safety is sufficient for any machine. The
OEM system integrator is responsible for analyzing the hazard and risks for a particular machine and
evaluate if the risks are sufficiently reduced by the provided safety functions.

System integrator responsibility

The OEM integrator is responsible for the following:

Maintaining an organization responsible for functional safety of the system

Ensuring that only authorized and trained personnel perform functional safety related work

Choosing reliable components

Completing a System Hazard & Risk Analysis and establishing the required risk reduction targets

Reassessing the hazard & risk every time the system is changed

Ensuring that the derived risks are properly reduced by the safety functions provided by the JS1-H
Steer by Wire steering joystick

Approving certification and homologation of the entire system to the desired risk reduction level

Installation, set-up, safety assessment, and validation of the interfacing sensor sub-systems

Validating that the safety functions reduce the risks as expected

Any related non-safety standards that should be fulfilled for the application and its components

Verifying the environmental robustness suitability of the JS1-H Steer by Wire steering joystick to
installation in the final system in its surrounding environment

Periodically inspecting for errata information updates

Safety architecture

The following illustration shows the abstract safety architecture of JS1-H Steer by Wire. Due to the
applicable safety requirements, the joystick implements different levels of redundancy for securing
safety-related functions.

User and Safety Manual

PLUS+1® JS1-H Steer by Wire

Functional Safety

 

16 | 

©

 Danfoss | December 2022

AX436683569858en-000101

Summary of Contents for PLUS+1 JS1-H


























Reviews: