manualshive.com logo in svg

Danfoss iC7-Marine PROFINET, Operating Manual, Page: 26 / 42

Share
Download
Danfoss iC7-Marine PROFINET Operating Manual Download Page 26

e30bl068.10

X2

X2

1

2

3

Figure 9:  Communication Port X0, X1, and X2 Locations in the Modular Control Unit

1

Ethernet port (X0)

2

Ethernet port (X1)

3

Ethernet port (X2)

3.5 

EMC-compliant Installation

3.5.1 

Overview

To obtain an EMC-compliant installation, follow the instructions provided in the product-specific design guide and the installation guide
included in the shipment.

3.5.2 

Grounding

l

Ensure that all stations connected to the fieldbus network are connected to the same ground potential. When distances between
the stations in a fieldbus network are long, connect the individual station to the same ground potential. Install equalizing cables
between the system components.

l

Establish a grounding connection with low HF impedance, for example, by mounting the unit on a conductive backplate.

l

Keep the ground wire connections as short as possible.

26

 | Danfoss Drives Oy © 2024.04                                                                                                                                                         AQ481922043454en-000101 / 172K4282A

Operating Guide | iC7-Marine PROFINET                                                                                                                                                                                              

Summary of Contents for iC7-Marine PROFINET











































Reviews:

No comments