Danfoss DEVIreg Smart Installation Manual Download Page 6 | Manualshive

Page: 6 / 28

background image

DEVIreg™ Smart

Installation Guide

6

Protection class

Class II -

Dimensions

85 x 85 x 20-24 mm
(in-wall depth: 22 mm)

Weight

127 g

*

not relevant for switch function

Electrical safety and Electro-Magnetic Compatibility for
this product is covered by the compliance with the EN/IEC
Standard “Automatic electrical controls for household and
similar use”:

• EN/IEC 60730-1 (general)
• EN/IEC 60730-2-9 (thermostat)

3

Safety Instructions

Make sure the mains supply to the thermostat/switch is
turned off before installation.

Important:

When the thermostat is used to control a

floor heating element in connection with a wooden floor
or similar material, always use a floor sensor and never set
the maximum floor temperature to more than 35°C.

«
...
4
5
6
7
8
...
»

Summary of Contents for DEVIreg Smart





























Reviews:

No comments

Related manuals for DEVIreg Smart

Brand: RADSON Pages: 6

tekmar tekmarNet 2

Brand: Watts Pages: 12

Brand: Dr.Frei Pages: 76

Kitchen Thermometer mini

Brand: iDevices Pages: 19

Brand: Livingstone Pages: 12

Brand: Endress+Hauser Pages: 12

Brand: White Rodgers Pages: 8

Brand: Inspire Pages: 10

Brand: RayTek Pages: 40

Brand: ABLE Asthma Pages: 9

Brand: Braun Pages: 5

Ecoflex Supra Standard ETN4

Brand: Uponor Pages: 32

Brand: DeDietrich Pages: 16

Brand: DeDietrich Pages: 16

Brand: Raychem Pages: 19

Brand: Campini Corel Pages: 2

Brand: Hama Pages: 108

Brand: SATO KEIRYOKI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands