Danfoss DEVIreg Smart Installation Manual Download Page 19 | Manualshive

Page: 19 / 28

background image

DEVIreg™ Smart

19

Installation Guide

6

Configuring

Download App

Download the DEVIsmart™ app from App Store
or Google Play or at devismart.com.

Find WiFi name and password for the WiFi
network, that you would like to connect your
thermostat/switch to. If in doubt contact net-
work administrator or internet service provider.

Identify your floor sensor type ( in kOhm).

Identify your installed output (in W), from
label on the heating element/equipment.

Power on the thermostat, and it will show “-“
in the display. Then it is ready to be configured
using your iPhone and Android device.

Open the DEVIsmart™ App. Follow instructions and set-
up flow in the App.

DEVIreg™ Smart indication

The DEVIreg™ Smart shows “–” indicating that power is
ON, but still need to be configured.

«
...
17
18
19
20
21
...
»

Summary of Contents for DEVIreg Smart





























Reviews:

No comments

Related manuals for DEVIreg Smart

Brand: Cockpit Pages: 7

Brand: Vega Technologies Pages: 2

Brand: B.Well Pages: 32

Brand: Hanna Instruments Pages: 2

Brand: YaliTech Pages: 2

Brand: EBECO Pages: 86

Thermo-Standard TS series

Brand: Rueger Pages: 4

Intellitherm C75

Brand: Fantini Cosmi Pages: 20

NixieTherm Mk III

Brand: Mr. Nixie Pages: 7

CEO-24-HC22 Series

Brand: SCI Pages: 32

Brand: Sinope Pages: 2

Brand: Watts Industries Pages: 4

Brand: flamco Pages: 28

Brand: CAME BPT Pages: 112

tekmarNet2 Thermostat 530

Brand: Tekmar Pages: 20

Brand: Technoline Pages: 2

Brand: Kinetik Pages: 2

Brand: VDH Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands