background image

 D
US

© Danfoss | Climate Solutions | 2023.09

AQ450437934291en-US0301 | 21

Relay position INT69 G

B2

12

14

11

Fig. 16

5

|

 Electrical connection    

Gauge state

Relay position

1.

Deactivated state

11-12

2.

INT69 G switch-on

11-14

3.

Remove PTC connector

11-12

4.

Insert PTC connector

11-12

5.

Reset after mains on

11-14

5.7  Oil sump heater

In order to avoid damage to the compressor, the compressor is equipped with an oil sump heater as 
a standard feature.

Operation:

 The oil sump heater operates when the compressor is at a standstill. 

 

When the compressor starts up, the oil sump heating switches off.

Connection: 

The oil sump heater must be connected via an auxiliary contact (or parallel wired auxiliary 

contact) of the compressor contactor to a separate electric circuit

.

Electrical data: 115 V  - 1 - 60 Hz, 80 W.

The oil sump heater must generally be connected and operated!

5.8  Selection and operation of compressors with frequency converters

For safe operation of the compressor, the frequency converter must be able to apply an overload of 

at least 160% of the compressor's maximum current (I-max.) for at least 3 seconds.

When using frequency converters, the following things must also be observed: 
1. The maximum permissible operating current of the compressor (I-max) (see type plate or 

technical data) must not be exceeded.

2. If abnormal vibrations occur in the system, the affected frequency ranges in the frequency 

converter must be blanked out accordingly.

3. The maximum output current of the frequency converter must be greater than the maximum 

current of the compressor (I-max).

4. After each compressor start, run for at least 1 minute at a frequency of at least 50 Hz.
5. Carry out all designs and installations in accordance with the local safety regulations and 

common rules (e.g. VDE) and regulations as well as in accordance with the specifications of the 

frequency converter manufacturer

 

The permissible frequency range can be found in the technical data. 

For compressors with LSPM motors, 

operation  with  frequency  converter  is  only  recommended 

in  delta  connection  with  corner  point  of  the  V/f  curve  277  V  /  60  Hz.  This  ensures  that  during 

operation  of  the  compressor,  within  the  permissible  frequency  band  and  application  limits,  the 

motor  does  not  fall  into  its  asynchronous  state  due  to  undervoltage/field  weakening  operation. 

 

For start-up and low speed operation, a voltage boost of 10-20 V is recommended to slightly reduce 

the motor current and compensate for voltage drops through the compressor supply line (and filtering 

devices, if present).

Summary of Contents for BOCK UL-HGX24 CO2 T Series







































Reviews: