ARM
Press the ESC switch until the LCD display reads as follows:
By pressing
ARM
(S1), the ARM software will become
active and the following changes take place in the LC
Display: See the example printed alongside the page.
You could then turn the
DATA ENTRY
wheel
until the desired module's
ARM
switch is lit.
The LC Display module number changes and the
ARM
switches switch lights change to the adjacent module (in either direction) as you
turn the wheel. In most cases it is faster to go to the module you would like to
route from and press the
local ARM
switch. The
ARM
switch in the selected
module lights up. By pressing any
ARM
switch, new module numbering
information in the LCD will appear and the corresponding
routing settings will be shown by the LEDs in the
ARM
section of that module. The LCDisplay shows the following
options while in the ARM mode>
MODULE SETUP COPYING
The
S1
(
Copy
) switch allows you to copy a selected module's setup to another
module or to as many (or all) modules you would prefer.
The following are easy steps describing this operation.
Step 1
: Select a module, press the
S1
(
Copy
) switch and
select another module (or all) with the
DATA ENTRY
control knob.
Step 2
: As soon as you hit
ENTER
all data will be copied to the selected
module (or all) and the data from these modules will be stored in Cinemix's
memory (on board microprocessor).
CLEAR
The clear switch restes all data on a module or on all modules.
UNDO
The undo switch un does all changes programmed earlier in that ARM session
only.
FADER CAL
The fader cal switch bypasses the fader position and adjust the channels fader
gain to unity. Motor faders will be positioned on their electrical 0dB position.
Note: Press ESC to leave the copy menu.
The ESC switch will take you out of the
ARM
menu. You can press an active
ARM
switch to achieve the same results. The
ARM
mode will show the
routing settings of the selected module.
Cinemix manual page: 24
CRM : - 10 dB
ARM Dyn Proj. Setup
CRM: -10dB Mod: 24
Copy Clr Undo Fdr cal
CRM: -10dB Mod: 24
Copy Clr Undo Fdr cal
CRM: -10dB Mod: 24
Copy to Module 23
Summary of Contents for CinemIX
