background image

 

2. Set vertical aiming of the first cabinet
The aiming of the first cabinet can be set to –7°, –3.5°, 0° or

+3.5°.
1. At the rear release both Locking pins of the cabinet's Splay link

from park position.

2. Fold out and insert the Splay link into the track of the Base

plate and align the hole of the link with the desired hole of the

Base plate.

3. Fix the angle of the cabinet using one Locking pin from the

Base plate.

3. Add further cabinets

Þ

At the front of the first cabinet release the Locking pins of the

Front links.

The Front links will slide out automatically.

4. Preset the splay angle
The splay angles between adjacent cabinets are defined using the

central rear rigging strands of the cabinets and can be set in the

range from 0° to 14° in 1° steps.

Þ

On the first cabinet, preselect the splay angle according to

your ArrayCalc simulation and insert and lock one Locking pin

in the appropriate hole.

5. Attach the next cabinet
1. Attach the next cabinet to the Front links.
2. Insert and lock the Locking pins on both sides.

Aiming of the first cabinet
Shown:
 –3.5°

 

d&b Z5396 Rigging manual 1.1 en

6

Summary of Contents for Z5396











Reviews: