此处安装舵机需用桐木块垫起一定高度
T
he
rudder and elevator
servo
s
should be
raised up
with a
paulownia block to
obtain the correct
height.
钢丝连杆穿入玻纤管，然后穿入机身，前端穿入F6-2/3固定，尾端穿入F10固定，
然后从侧板预留孔穿出。
Insert the steel wire rod into the fiberglass tube,
insert
this assembly
into the
fuselage.
The front end
of F6-2&3 are
fixed
at former
F6, the tail end
s are
fixed by
former
F10, and then
passed through the slots in the fuselage sides.
快装接头
M4
M2R
M3
轻木条
M1L
M5
M0玻纤+M0*2
自攻螺丝
自攻螺丝拧
到轻木条上
Screw the
self-tapping screws
i
nto
the ply
wood
self-tapping screws
电机安装示范，电机座根据所选电机调整伸出长度，
调整好后用角型铝件固定住。
Motor
mount installation. T
he motor mounting
slides into
the front fuselage former. Adjust the
length according to the
motor you have
selected
. Once you have determined the
exact position i
t is fixed
in place using the 2
angle
d
aluminum piece
s as shown
.
5
09
Assemble the servo inside the fuselage
机身内舵机安装
10
Install the Motor Mounting and Motor
电机座及电机安装
11
Install the scale parts
像真件安装
此机型结构为电动马达设计，如您需要安装油动引擎，我们为您提供了2块油动引
擎防火墙，安装需要一定的改装和加固，需要您自己动手修改。
This model is designed for
an
electric motor. If you
wish
to install
an I.C.
engine
then
we provide you with 2 engine firewalls. The installation needs
certain modification and reinforcement. You
will
need to modify
th
e
airframe
yourself.
副翼连接舵机
Connecting aileron servo
襟翼连接舵机
Connecting flap servo
EZ-Connector
垂直尾翼连接舵机
Rudder horn and pushrod
assembly
水平尾翼连接舵机
Elevator horn and pushrod assembly
此处轻木条根据马达座与
角型铝件结合的位置调整
Here the
hard
wood strip
is adjusted according to
the position of the motor
mounting and the angled
aluminum
mount
.
fiberglass
另一边相同安装
Same installation
on the other side
Hard
wood Strip
F6-2
F6
F10
F6-3
F6-2
/3
调整到合适位置后粘贴到F6板上。
F6-2
and F6-3 are set
to the appropriate
position and then
glued
to the
former
F6.
快装接头
EZ-Connector
注意：您在修修剪PVC舱罩时，需参考仓身前部
F4-1木件的预留凹槽的孔位修剪出两个卡扣。
在安装时，卡扣嵌入凹槽内。（具体见下图）
Note: When trimming the
clear
PVC
top
hatch
you
will
need to trim the
2 front lugs
to fit into
the
slots
in F4-1
, this is the
wooden part
at the top
front of the cabin.
Wh
en
fitting
the
lugs
need to
fit into the
slots as shown
.
