manualshive.com logo in svg

DALBO GREENLINE 300, Manual

Share
Download
DALBO GREENLINE 300 Manual Download Page 28

 

 

GREENLINE 

 

 

 

Side 28 

 

Assembly 

1

 

Fit new gaskets (pos. 5+6+7+8+9) in upper part, plus collar shoe. 

2

 

Lubricate thread in upper part (pos. 3) and cylinder tube (pos. 1) with grease or 
oil. 

3

 

Fit upper part (pos. 3) on ram shaft. 

4

 

 Fit collar shoe (pos. 4) and screw on lock nut, 

secure with Loctite

. Ensure that 

thread is absolutely clean and free of oil or other impurities before applying Loc-
tite.

 Do not fill with oil for 12 hours after use of Loctite.

 

5

 

Lubricate  outer  collar  shoe  gasket  in  contact  with  cylinder  tube  and  inside  of 
cylinder tube with oil, push ram into centre position. 

6

 

Fit upper part onto cylinder tube and tighten. 

7

 

For fitting cylinder see ”

Replacing harrow depth-adjustment cylinder 

”.

 

 

Removal/fitting wheel 

Before  removing  wheel,  fully  extend  roller  to  rest  on  ground.  Wheels  will  then  be 
raised free of ground.  
Remove wheel nuts. Remove wheel. Replace wheel, hand-tighten wheel nuts. Lower 
wheels to ground. Tighten wheel nuts to 300 Nm. 
 

 

Ensure wheel nuts and wheel surfaces are clean to avoid nuts loosening. 
 

 

Replacing wheel bearings 

 

Fig. 36 

1.

 

Remove hub cap pos. 21 

2.

 

Remove split pin pos. 20. 

3.

 

Remove castle nut pos. 19. 

4.

 

Tap out axle pos. 2 

5.

 

Remove bearings pos. 17+18 

6.

 

Remove seal ring pos. 16 

 

 

Summary of Contents for GREENLINE 300

































Reviews:

No comments

Brands by name

Popular brands

Load more brands