manualshive.com logo in svg

DALBO GREENLINE 300, Manual

Share
Download
DALBO GREENLINE 300 Manual Download Page 22

 

 

GREENLINE 

 

 

 

Side 22 

 

Adjustment  

Wheels 

Lubricate and adjust wheel bearings at least once annually. Check tyre pressures 
(see recommended pressure on tyre).  
 
Adjustment and lubrication of wheel bearings 
1.

 

Remove hub caps. 

2.

 

Remove split pin. 

3.

 

Tighten castle nut 1/6th of a turn until hole aligns with axle. Turn wheel, check 
for resistance. A little play should be detected in the hub housing when rocking 
wheel from side to side. If play is excessive, repeat process. 

4.

 

Replace split pin 

5.

 

Fill hub cap ¾ full with grease. Replace. 

 

Scraper 

 

Fig. 11 

Adjust scraper as required.  

1.

 

Slacken  bolts  (A).  Scraper  can 
be pushed closer to roller. 

2.

 

Tighten bolts 

Scraper  must  not  be  in  direct  contact 
with roller. 

 

Hydraulics 

 

Check all hydraulic hoses for wear or cracks. Check all hoses for crimping. 

 

 

Lubricate exposed rams with oil or pressure-resistant grease to avoid rust forming 
when storing for long periods. Remember to remove before use. 

 

A 

 

Summary of Contents for GREENLINE 300

































Reviews:

No comments

Brands by name

Popular brands

Load more brands