manualshive.com logo in svg

DAL-BO Maxiroll 1030 2008, Manual

Share
Download
DAL-BO Maxiroll 1030 2008 Manual Download Page 31

 

 

Maxiroll 2008 

 

 

Page 31 

Replacing pendulum frame suspension cylinder  

 

Fig. 27 

1.

 

Extend  roller  resting  on  a 
level surface 

2.

 

Set  tractor  hydraulic  control 
handle  in  flow  setting.  Set 
manometer  handle  in  flow 
setting.  Pressure  will  flow 
back into the tractor.  

3.

 

Disconnect  hoses  from  cy-
linders 

4.

 

Remove  split  pins  and  pins 
(B) 

5.

 

Fit  new  or  repaired  cylinder 
(A) 

6.

 

Remember  to  replace  split 
pins in pins 

 

 

 

Activate  depth-adjustment  cylinders  up  and  down  a  few 
times after fitting and with roller extended, to bleed system. 

 

Replacing gasket set for suspension 

Fig. 28 

 

Cylinder 50/30-150 

 
1

 

Drain oil from cylinder by moving ram carefully backwards and forwards. 

2

 

Extend ram to centre position. Unscrew upper part (pos. 3) from cylinder 
tube (pos. 1). Use special tool to remove upper part. If upper part is stuck, 
heat front of upper part. When upper part is detached from cylinder tube, 
pull ram up towards upper part and remove completely from cylinder tube 
(pos. 1). 

3

 

Remove lock nut (pos. 10) securing collar shoe (pos. 4). 

4

 

Remove collar shoe (pos. 4) from ram shaft, (pos. 2). 

5

 

Remove upper part (pos. 3) from ram shaft, (pos. 2). 

6

 

Remove gaskets in upper part (pos. 5+6+7+8+9) along with collar shoe. 

B 

Summary of Contents for Maxiroll 1030 2008











































Reviews:

No comments

Brands by name

Popular brands

Load more brands