manualshive.com logo in svg

Daktronics VIP-5000 Series, Operation Manual, Page: 12 / 62

Share
Download
Daktronics VIP-5000 Series Operation Manual Download Page 12

– 8 –

3  User Interface Basics

Interface Elements

The VIP-5000 series processor interface includes elements that are always visible to the 

operator, including a header bar, left-side menu, right-side menu, and main window. 

Refer to 

Figure 21

.

Header bar

Left-side menu

Right-side menu

Status tiles

Main window

Figure 21: 

Interface Elements

•  Header bar

 contains the application title across the top of the screen.

•  Right-side menu

 is in the upper-right corner of the screen. Click 

User

 

 to expand 

the menu panel to show the full session-specific navigation information. Refer to 

Right-Side Menu (p. 9)

 for more information.

•  Left-side menu

 is on the left side of the screen. Click 

Show Menu

 

 in the upper-

left corner of the screen to expand the menu panel to show the full navigation 

information. Refer to 

Left-Side Menu (p. 10)

 for more information.

•  Main window

 displays elements, information, and data related to current operator 

selections and system triggers. The example in 

Figure 21

 above shows the initial 

Dashboard

 screen with status tiles in the main window.

Summary of Contents for VIP-5000 Series































































Reviews:

No comments