manualshive.com logo in svg

Daktronics VIP-5000 Series, Operation Manual, Page: 14 / 62

Share
Download
Daktronics VIP-5000 Series Operation Manual Download Page 14

– 10 –

Password

Password

 opens a window that enables the operator 

to change their password. Enter the new password 

and confirm the change. Refer to 

Figure 23

.

After entering a new password and confirming it, click 

Save

 at the top to save the changed password. Click 

Cancel

 to close the 

Password

 window without saving 

the new password and return to the 

Dashboard

.

After a new password is saved, the operator is logged 

out and returned to the login prompt. Log in again 

using the new password.

Help

Help

 opens a window that provides an online version of this manual.

About

About

 opens a window with a link to the Daktronics website and the Daktronics customer 

support number. There is a link to licensing information showing the open source libraries 

and licenses used to build the VIP-5000 series processor.

Legacy

Legacy

 opens the older version of the VIP user interface in a new browser window. Within 

the legacy interface, click the help button 

 in the upper-left corner to access the 

legacy interface’s manual.

Left-Side Menu

This section describes the tools and features available in the left-side column. Click 

Show 

Menu

 

 in the upper-left corner of the screen to expand the main menu panel to show 

the full system navigation information. Refer to the table below. Refer to 

Section 4: 

Dashboard (p. 11) - Section 10: System Backup (p. 43)

 for a description of each 

left-side menu item.

Menu Item

Description

Shows status tiles for various aspects of the processor; most tiles trigger 

operational windows but some tiles only provide information

Lists all current configuration settings and tools including tools for setting 

the input, output, brightness levels, local time, and location

Opens a window showing a video feed of the display content

Shows existing stored content files and allows images to be added or 

removed

Lists troubleshooting options including testing, resetting power, and 

resetting the processor

Lists calibration tools used to adjust individual modules to blend with 

surrounding modules

Lists system backup options including creating a system backup and 

restoring a system backup

Figure 23: 

Password Function

Summary of Contents for VIP-5000 Series































































Reviews:

No comments