Daktronics RC-200 Operation Manual Download Page 7

Page: 7 / 80

Introduction

1 Introduction

This manual is designed to explain the operation of the Daktronics RC-200 Remote

Control System for All Sport

applications. For additional information regarding the safety,

installation, operation, or service of this system, refer to the telephone numbers listed in

Daktronics Exchange and Repair & Return Programs (p�2)

Important Safeguards

•

Read and understand all instructions, both general and for specific applications.

•

Always turn off and/or unplug the control equipment when it is not in use� Never yank

the power cord to pull the plug from the outlet� Grasp the plug and pull to disconnect�

•

Do not drop the control console or allow it to get wet�

•

Do not disassemble control equipment or electronic controls of the display; failure to

follow this safeguard will make the warranty null and void�

•

Do not let any power cord touch hot surfaces or hang over the edge of a table that

would damage or cut the cord�

•

If an extension cord is necessary, use a three-pronged, polarized cord� Arrange the

cord with care so that it will not be tripped over or pulled out�

•

Inspect console for shipping damage such as rattles and dents, and verify that all

equipment is included as itemized on the packing slip� Immediately report any

problems to Daktronics; save all packing materials if exchange is necessary�

•

Use only the 18 VDC wallpack charger or charging station provided from Daktronics

for recharging the battery� Refer to Battery Recharging (p�5)�

CAUTION! RISK OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED�
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS�

Specifications Label

Power specifications as well as product assembly

information can be found on an ID label on the back

of the handheld device and on the bottom of the

base station, similar to those shown in

Figure 1

When calling Daktronics customer service,

please have the assembly number and the date

manufactured available to ensure the request is

serviced as quickly as possible.

Recommended Temperatures

•

Operation:

14° to 149° Fahrenheit (-10° to 65° Celsius)

•

Charging:

32° to 104° Fahrenheit (0° to 40° Celsius)

•

Storage:

-4° to 113° Fahrenheit (-20° to 45° Celsius)

Resources

Figure 2

illustrates a Daktronics drawing label. This

manual refers to drawings by listing the last set of digits.

In the example, the drawing would be referred to as

DWG-1007804

. All references to drawing numbers,

appendices, figures, or other manuals are presented in

bold typeface.

ASSY NO.

SER. NO.

MFG DATE

BROOKINGS, SD 57006-5128 PHONE 800-325-8766

LL-2305 R01

201 DAKTRONICS DR.

DAKTRONICS

Wireless Handheld:

Wireless Base Station:

ASSY NO.

SER. NO.

MFG DATE

BROOKINGS, SD 57006-5128 PHONE 800-325-8766

LL-2305 R01

201 DAKTRONICS DR.

DAKTRONICS

0A-1110-0062

S/N: ####

(DATE) REV ##

POWER: 18V , 1.1A

MODEL: DAKT-0406-00

0A-1110-0067

S/N: ####

(DATE) REV ##

POWER: 12-18V , 0.1A

MODEL: DAKT-0406-00

Figure 1:

Specifications Labels

Drawing Number

Figure 2:

Drawing Label

Summary of Contents for RC-200

















































































Search results

Summary of Contents for RC-200

Reviews:

Related manuals for RC-200

Brands by name

Popular brands

Daktronics RC-200, Operation Manual

Search results

Summary of Contents for RC-200

Reviews:

Related manuals for RC-200

Brands by name

Popular brands