THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS
DRAWING ARE CONFIDENTIAL AND PROPRIETARY. DO NOT
REPRODUCE BY ANY MEANS WITHOUT THE EXPRESSED
WRITTEN CONSENT OF DAKTRONICS, INC.
COPYRIGHT 2012 DAKTRONICS, INC.
DAKTRONICS, INC.
AV
DRAWN:
DATE:
SHEET
JOB NO:
REV
ALL SPORT RADIO / RC-100
OUTDOOR INSTALLATION; GEN VI RADIO & BASE STATION
MMILLER
08 AUG 12
P1110
F 01 A
NONE
MMILLER
1109252
02
FROM 2.4GHZ RADIO
RECEIVER
FROM RC-100 BASE
STATION
TX RX
IN
TX RX
CL / RS232
RANGE
CAN
RC-100 BASE STATION VIEW
ALLSPORT 2.4GHZ RADIO RECEIVER VIEW
STEP 1
REFER TO DWG-01109181 FOR INSTRUCTIONS ON SETTING THE CHANNEL AND
MOUNTING INSIDE THE SCOREBOARD
STEP 1
REFER TO DWG-00236394 FOR INSTRUCTIONS ON SETTING THE CHANNEL
AND MOUNTING INSIDE THE POWER/SIGNAL ACCESS DOOR.
**SECOND 9/32" HOLE WILL NEED TO BE DRILLED INTO SCOREBOARD FRONT
PANEL TO ATTACH THE SECOND ANTENNA
DRAWING USED TO CONNECT TWO RADIOS TO THE SAME DRIVER.
NOTE: THE TWO RECEIVERS SHOULD BE MOUNTED A COUPLE FEET APART
ONLY ONE WIRELESS CONTROLLER CAN BE USED AT A TIME.
CHANNEL DIAL AND BCAST DIAL LOCATIONS ON RADIO
RECEIVER; COVER REMOVED.
FUNC
CHAN
BCAST
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
0
1
2
3
4
5
6
7
8
GREEN - POWER LED
RED - DATA LED
AMBER - STATUS LED
ADD SECOND CABLE
FROM THE BASE
STATION KIT.
"RADIO" ON THE
DRIVER.
"RC-100" ON THE
DRIVER.
LEGACY VIEW
GYRUS VIEW
FROM RC-100 BASE
STATION
FROM 2.4GHZ RADIO
RECEIVER
DATE:
REV
BY:
01
18 FEB 15
BJG
ADDED GYRUS VIEW
UPDATED CONNECTORS FOR LEGACY VIEW
W-2914
6-PIN PLUG
W-2913 @2
- PLUG THE 6-PIN MALE END OF THE RADIO SPLITTER CABLE (W-2914)
INTO THE MATING 6-PIN JACK (J21) ON THE DRIVER.
- PLUG THE 6 PIN MALE PLUGS FROM BOTH THE RECEIVER AND THE
BASE STATION INTO THE MATING 6-PIN JACKS OF THE RADIO
SPLITTER. IT DOES NOT MATTER WHICH PLUG CONNECTS TO WHICH
JACK.
-RC-100 BASE STATION REQUIRES FIRMWARE VERSION 3.7 OR
GREATER.
-GEN VI RADIO RECEIVER REQUIRES FIRMWARE VERSION 1.4 OR
GREATER.
- PLUG THE 6-PIN MALE PLUG FROM THE RADIO RECEIVER INTO THE
MATING 6-PIN JACK OF AN ADAPTOR HARNESS (W-2913).
- PLUG THE MALE 5-PIN END OF THE ADAPTOR HARNESS INTO THE
MATING 5-PIN CONNECTOR (J45) COMING FROM THE DRIVER. VERIFY THE
OTHER END OF THIS J45 HARNESS IS CONNECTED TO THE J21 (RADIO)
ON THE DRIVER.
- ADD A SECOND J45 HARNESS (0A-1388-0004) AND CONNECT THE 4-PIN
PLUG END TO THE J22 (RC-100) ON THE DRIVER.
- PLUG THE 6-PIN MALE PLUG FROM THE BASE STATION INTO THE
MATING 6-PIN JACK OF ANOTHER ADAPTER HARNESS (W-2913).
- PLUG THE MALE 5-PIN END OF THE ADAPTOR HARNESS INTO THE 5-PIN
CONNECTOR (J45) THAT WAS JUST INSTALLED ON THE DRIVER.
DATE:
REV
BY:
02
3 SEP 15
MTR
ADDED RC-100 AND GEN VI FIRMEARE NOTES
