background image

TROUBLE SHOOTING GUIDE 

Symptom 

   Possible 

Problem 

  Solution 

---------------------------------------------------------------------------------------------------------------------------------------------------- 
System will not operate.  

 

Receiver is not getting   

 

Check 12 volt connection. 

      

 

power. 

    Check 

ground 

connection. 

 

 

 

 

 

 

 

 

 

 

Check fuses. 

 

 

 

 

 

Transmitter is locked. 

 

 

Press V and VI at the same 

 

 

 

 

 

 

 

 

 

 

  time. 

     Antenna 

is 

not 

plugged 

in. 

 Check 

antenna 

connection. 

     System 

is 

in 

test/program 

mode 

 Check 

Switch 

#7 

Door latch actuators ‘jump’ 

 

Weak or poor 12 volt connection. 

Check 12 volt connection to  

  or ‘chatter’. 

 

   

 

                                                                    Relays. 

 

 

 

 

                                                                                                        Move to new terminal point. 

Windows change direction in 

 

Over loaded 12 volt power circuit. 

Place receiver and windows on 

 

 

mid-travel. 

         

 

separate 

circuits. 

          Check 

for 

loose 

connections. 

          Increase 

wire 

size 

on 

power. 

    Weak 

car 

battery. 

  Recharge 

or 

replace 

car 

battery. 

Transmitter signal is being disrupted. 

Move antenna away from power     
wires. 

Outputs 1 and 2 work, but all others 

Ignition key is on. 

 

 

Turn off ignition key. 

  will not 

 

 

 

IGN terminal has 12 volts at all times. 

Move IGN wire to a 

terminal  
          that 

is 

powered 

only 

when 

the 

key is on. 

Transmitter has very short range 

Transmitter battery is weak. 

 

See Battery Replacement. 

  on all functions. 

 

 

Antenna needs repositioning 

 

Move antenna out away from 
  any high current wires. 

 
If none of these solutions solve the problem, or the problem occurring is not listed here, please call the Dakota 
Digital technical assistance line at (605) 332-6513 for further assistance or email to: 
[email protected] 
 

CMDX COMMANDER SERIES REMOTE ENTRY SYSTEM LIMITED LIFETIME WARRANTY 

DAKOTA DIGITAL (the Company) warrants to the ORIGINAL PURCHASER of this remote control product that should any included 

control relays, electronic module, or transmitters under normal use and condition, be proven defective in material or workmanship DURING 
THE LIFETIME OF THE CAR IN WHICH IT WAS ORIGINALLY INSTALLED, such defect(s) will be repaired or replaced (at the Company’s 
option) without charge for parts or labor directly related to repairs of the defect(s). 

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. 

dated bill of sale), specification of defects, transportation prepaid, to the factory.  This Warranty is valid for the original purchaser only and may 
not be transferred. 

This warranty does not cover batteries, nor extend to damage to vehicle electrical system.  This Warranty does not apply to any 

product or part thereof which in the opinion of the Company has been damaged through alteration, improper installation, mishandling, misuse, 
neglect, or accident. 

This Warranty is in lieu of all other express warranties or liabilities.  ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED 

WARRANTY OF MERCHANTABLITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.  ANY ACTION FOR 
BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABLITY MUST BE BROUGHT 
WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE.  IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY 
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, 
WHATSOEVER.  No person or representative is authorized to assume for the Company any liability other that expressed herein in connection 
with the sale of this product. 

The Company does not warrant that this product cannot be compromised or circumvented.  THE EXTENT OF THE COMPANY’S 

LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL 
THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE PAID BE THE PURCHASER FOR THE PRODUCT. 

 

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation if incidental or consequential 

damage so the above limitations or exclusions may not apply to you.  This warranty gives you specific legal rights and you may also have 
other rights which vary from state to state. 

  

4510 W. 61ST St. N.,  Sioux Falls, SD  57107 

Phone: (605) 332-6513      FAX: (605) 339-4106

 

www.dakotadigital.com 

[email protected] 

    ©Copyright 2005 Dakota Digital Inc.

 

 

14

Summary of Contents for COMMANDER Series















Reviews: