Daitsu ACCD LIBERTY Series Installation And Maintenance Manual Download Page 24

Page: 24 / 30

Wired Remote Controller

ACCD_WC2

Table 4 Meaning of Each Error

Error

Code

Error

Code

Drive board communication error

Return air temperature sensor open/short

circuited

Compressor overheating protection

evaporator temperature sensor open/short

circuited

Indoor and outdoor units unmatched

Indoor unit liquid valve temperature sensor

open/short circuited

IPM temperature sensor open/short circuited

Communication line misconnected or

expansion valve error

Indoor gas valve temperature sensor open/

short circuited

Pump-down

Defrost or oil return

Outdoor ambient temperature sensor open/

short circuited

Outdoor unit condenser mid-tube temperature

sensor open/short circuited

Forced defrosting

Indoor and outdoor communication error

Compressor startup failure

DC bus under-voltage protection

High discharge temperature protection

DC bus over-voltage protection

PH Overload protection

Discharge temperature sensor open/short

circuited

Whole unit over-current protection

Compressor demagnetization protection

HE Over phase current protection

PFC protection

Compressor desynchronizing

IPM Current protection

IPM Temperature Protection

Over-power protection

Compressor phase current sensing circuit

error

Compressor phase loss/reversal

protection

Capacitor charging error

Frequency restricted/reduced with whole

unit current protection

System charge shortage or blockage

protection

High pressure protection

Frequency restricted/reduced with IPM

current protection

Low pressure protection

Frequency restricted/reduced with high

discharge temperature

Compressor stalling

Frequency restricted/reduced with anti-

freezing protection

Over-speeding

Frequency restricted/reduced with

overload protection

Drive board temperature sensor error

Indoor unit full water error

AC contactor protection

Anti-freezing protection

Temperature drift protection

AC input voltage abnormal

Sensor connection protection

Whole unit current sensing circuit error

DC bus voltage drop error

4-way valve reversing error

Frequency restricted/reduced with IPM

temperature protection

Outdoor fan 1 error protection

Motor stalling

Outdoor fan 2 error protection

PG motor zero-crossing protection

Summary of Contents for ACCD LIBERTY Series































Search results

Summary of Contents for ACCD LIBERTY Series

Reviews:

Brands by name

Popular brands

Daitsu ACCD LIBERTY Series, Installation And Maintenance Manual

Search results

Summary of Contents for ACCD LIBERTY Series

Reviews:

Brands by name

Popular brands