background image

16

Check the following before requesting 
service

NOTE

Check the above items, and if the problem still cannot be fixed, contact your dealer for repair, stating the symptom(s) and 
the model name.

Symptom

If the display “        ” (INSPECTION), 
UNIT No.” and the OPERATION 
lamp flash and “MALFUNCTION 
CODE” appears.

Action and contact

Inform your dealer of the contents of the display on the remote contoller.

C

H

UNIT No.

OPERATION lamp

INDOOR UNIT No. in which a malfunction occurs

MALFUNCTION CODE

INSPECTION
display

Safety equipment such as fuses, 
circuit breakers, leakage breaker, etc. 
are set off occasionally.

Operating switch function is not secure.

Water leaks from the air conditioner.

Do not set power switch to on.

Set power switch to off.                 

Stop operation.

Symptom

The machine does not work at all.

The machine runs but stops soon.

The machine does not work 
properly.

Cause

Remedy

Blocked air inlet or air outlet of indoor 
or outdoor unit

Blown fuse or open breaker

Power outage

If the main power supply is turned off 
during operation, operation will restart 
automatically after power turns back again.

Replace the fuse or close the breaker.

Blocked air inlet or air outlet of the 
indoor or outdoor unit

Remove the obstacle.

Improper temperature setting

Low fan speed setting

Improper air flow direction

Window or door open

Direct sunshine

Too many people in the room

Too many heat sources in the room

If the air filter clogged.

Remove the obstacle.

See page 7.

See page 8.

See page 10.

Close.

Put up a curtain or blind over the window.

Refer to the instruction manual of 
the indoor unit, and clean the air filter.

02_EN_3PN07192-6E.fm  Page 16  Monday, January 17, 2011  1:52 PM

Summary of Contents for RXYMQ4PVET





















Reviews: