background image

9

Program DRY Operation

Program DRY

 is 

a function

 that 

alternates between weak cooling and stopping the unit

 to remove humidity from the 

air, in order to prevent the room temperature from dropping and becoming too cold.

The microcomputer 

automatically

 controls the temperature and fan strength, so these cannot be set using the remote 

controller.

This function is not available if the room temperature is 16°C or lower.

FOR SYSTEMS WITHOUT COOL/HEAT CHANGEOVER REMOTE CONTROLLER

1.

Press OPERATION MODE SELECTOR button several times and select “

” (PROGRAM DRY Operation).

2.

Press ON/OFF button.

OPERATION lamp lights up and system starts OPERATION.

FOR SYSTEMS WITH COOL/HEAT CHANGEOVER REMOTE CONTROLLER (Only for the heat pump)

1.

Select cooling operation mode with the cool/heat changeover remote controller.

2.

Press OPERATION MODE SELECTOR button several times and select “

” (PROGRAM DRY Operation).

3.

Press ON/OFF button.

OPERATION lamp lights up and system starts OPERATION.

4.

Press AIR FLOW DIRECTION ADJUST button. 

(only for FXCQ, FXFQ, FXHQ, FXAQ)

This operation is not available with the BRC1A62 remote controller.
Refer to page 10 for details.

5.

Press ON/OFF button again.

OPERATION lamp goes off, and the system stops OPERATION.

ATTENTION:

Do not turn OFF power immediately after the unit stops. Then, wait on no less than 5 minutes. Water is leaking or there 
is something else wrong with the unit.

TEST

2·5

4

1

For the BRC1C61

2·5

4

1

For the BRC1A61

The situation is the same for the BRC1A62.

BRC1A61

only

3-5

2

4

1

1

3-5

4

2

For the BRC1C61

For the BRC1A61

Adjustment

STOPPING THE SYSTEM

02_EN_3PN07192-6E.fm  Page 9  Monday, January 17, 2011  1:52 PM

Summary of Contents for RXYMQ4PVET





















Reviews: