background image

11

English

When attaching the drain pan heater

In high humidity areas or heavy snow areas, it is recommended to attach a drain pan heater to 
prevent ice build-up from the bottom frame.

1) 

Attach the drain pan heater in accordance with the installation manual included with the drain pan heater.

2) 

Dismount the service lid by removing the 2 screws.

3) Remove the switch cover (1 screw).
4) Turn on SW6-1 on the PCB.

PCB

HEAT

COOL

4

3

2

1

2

1

E

D

C

B

A

ON

OFF

2

1

SW6

1

2

Turn on 
switch 1

Screw

Remove 
the switch 
cover

Pump Down Operation

In order to protect the environment, be sure to pump down when relocating or disposing of the unit. 

1) 

Remove the valve cap from the liquid stop valve and gas stop valve.

2) 

Begin forced cooling operation.

3) After 5 to 10 minutes, close the liquid stop valve with a hexagonal wrench.
4) 

After 2 to 3 minutes, close the gas stop valve and stop forced cooling operation.

5) 

Attach the valve cap once procedures are complete.

Liquid 
stop valve

Hexagonal 

wrench

Valve cap

Close

Gas  
stop valve

Forced cooling operation

 

„

Using the indoor unit ON/OFF switch 

Press the indoor unit ON/OFF switch for at least 5 seconds. (The operation will start.) 

•  Forced cooling operation will stop automatically after about 15 minutes. 

To stop the operation, press the indoor unit ON/OFF switch.

 

„

Using the indoor unit’s remote controller

1) 

Press 

 and select the COOL operation.

2) 

Press 

 to turn on the system.

3) 

Press 

 , 

 and 

 at the same time. 

4) 

Press 

 , select “ 

 ”, and press 

 for confirmation.

• 

Forced cooling operation will stop automatically after about 30 minutes. To stop the operation, 

press 

 .

01_EN_3P628775-3.indd   11

2021/02/09   13:40:07

Summary of Contents for RXM18VVJU















Reviews: