background image

2 About the documentation

Installer reference guide

7

RXF50+60B2_RXF71A2_RXP50~71L2_(A)RXM42~71N2_RXJ50N2_
RXA42+50B2
R32 split series
4P513661-6B – 2018.05

2

About the documentation

2.1

About this document

INFORMATION

Make sure that the user has the printed documentation and
ask him/her to keep it for future reference.

Target audience

Authorised installers

Documentation set

This  document  is  part  of  a  documentation  set.  The  complete  set
consists of:

General safety precautions:

▪ Safety instructions that you MUST read before installing

▪ Format: Paper (in the box of the outdoor unit)

Outdoor unit installation manual:

▪ Installation instructions

▪ Format: Paper (in the box of the outdoor unit)

Installer reference guide:

▪ Preparation of the installation, reference data,…

▪ Format:  Digital  files  on 

http://www.daikineurope.com/support-

and-manuals/product-information/

Latest revisions of the supplied documentation may be available on
the regional Daikin website or via your dealer.

The original documentation is written in English. All other languages
are translations.

Technical engineering data

▪ A 

subset

  of  the  latest  technical  data  is  available  on  the  regional

Daikin website (publicly accessible).

▪ The 

full  set

  of  latest  technical  data  is  available  on  the  Daikin

extranet (authentication required).

2.2

Installer reference guide at a
glance

Chapter

Description

General safety
precautions

Safety instructions that you MUST read
before installing

About the documentation

What documentation exists for the
installer

About the box

How to unpack the units and remove
their accessories

About the unit

How to identify the unit

Preparation

What to do and know before going
on‑site

Installation

What to do and know to install the
system

Configuration

What to do and know to configure the
system after it is installed

Commissioning

What to do and know to commission the
system after it is configured

Hand‑over to the user

What to give and explain to the user

Maintenance and service

How to maintain and service the units

Troubleshooting

What to do in case of problems

Disposal

How to dispose of the system

Technical data

Specifications of the system

Glossary

Definition of terms

3

About the box

3.1

Overview: About the box

This  chapter  describes  what  you  have  to  do  after  the  box  with  the
outdoor unit is delivered on-site.

It contains information about:

▪ Unpacking and handling the units

▪ Removing the accessories from the units

Keep the following in mind:

▪ At delivery, the unit MUST be checked for damage. Any damage

MUST be reported immediately to the carrier's claims agent.

▪ Bring  the  packed  unit  as  close  as  possible  to  its  final  installation

position to prevent damage during transport.

▪ Prepare the path along which you want to bring the unit inside in

advance.

▪ When handling the unit, take into account the following:

Fragile, handle the unit with care.

Keep the unit upright in order to avoid damage.

Keep the unit away from rain or damp conditions.

At least 2 persons MUST handle the box with the unit.

3.2

Outdoor unit

3.2.1

To unpack the outdoor unit

Summary of Contents for RXF60B2V1B





























Reviews: