background image

Outdoor Unit Installation Drawings

Installation Guidelines

• Where a wall or other obstacle is in the path of outdoor unit’s intake or exhaust airflow, follow the 

installation guidelines below.

• For any of the below installation patterns, the wall height on the exhaust side should be 47-1/4 inch 

(1200mm) or less.

* Be sure to add the proper amount of additional refrigerant. 

Failure to do so may result in reduced performance.

Max. allowable height

Max. allowable length

98.4ft (30m)

65.6ft (20m)

Model

30/36 class

Liquid pipe

Gas pipe

O.D. 3/8 inch (9.5mm)

O.D. 5/8 inch (15.9mm)

0.55oz/ft

(50g/m)

Additional refrigerant 
required for refrigerant 
pipe exceeding 32ft 
(10m) in length.

Min. allowable length

6.6ft (2m)

More than 1-15/16”

(50mm)

More 
than 
3-15/16”
(100mm)

More than 13-3/4” (350mm)

47-1/4” 
(1200mm)
or less

More than 1-15/16”

(50mm)

More than 
13-3/4”
(350mm)

Wrap the insulation 
pipe with the finishing 
tape from bottom to top.

Allow 11-13/16 inch (300mm) 
of work space below the 
ceiling surface.

9-7/8” (250mm) from w

all

Allow space for piping 
and electrical servicing.

Right side plate

13-5/8”

(345mm)

Clamping material

Insulation tube

Bottom frame

Tape

Also insulate the connection on the outdoor unit.

Use tape or insulating material on all connections 
to prevent air from getting in between the copper 
piping and the insulation tube.
Be sure to do this if the outdoor unit is installed 
above.

(F

oot bolt-hole 

 centres)

(Foot bolt-hole centres)

24-7/16”

(620mm)

Level mounting base 
(available separately)

If there is the danger of the unit falling 
or overturning, fix the unit with 
foundation bolts, or with wire or other 
means.

If the location does not have good 
drainage, place the unit on a level 
mounting base (or a plastic pedestal). 
Install the outdoor unit in a level 
position. Failure to do so may result in 
water leakage or accumulation.

More than 3-15/16”

(100mm)

Side view

Wall facing one side

Top view

Walls facing two sides

Top view

More than 3-15/16”

(100mm)

More than 13-3/4”

(350mm)

More than 1-15/16”

(50mm)

Walls facing three sides

CAUTION

Set the piping length 
from 6.6ft (2m) to 98.4ft (30m).

Summary of Contents for RKS30














Reviews: