background image

13 

English

REMOTE CONTROL SETTING

10-2 

Forced off and ON/OFF operation should be selected by 

• 

selecting the SECOND CODE  NO. as shown in Table 4.

Table 4

External ON/OFF input

Mode No.

FIRST 

CODE NO.

SECOND 

CODE NO.

Forced off

12 (22)

1

01*

ON/OFF operation

02

* factory set

Input A of forced off and ON/OFF operation work as shown 

• 

in Table 5.

Table 5

Forced off

ON/OFF operation

Input A “on” to force a stop 
(remote controller reception 
prohibited)

Unit operated by changing input 
A from “off” to “on”

Input A “off” to allow remote 
controller

Unit stopped by changing input A 
from “on” to “off”

SETTING THE FILTER SIGN DISPLAY INTERVAL

10-3 

Explain the following to the customer if the fi lter dirt settings 

• 

have been changed.
The fi lter sign display time is set to 2500 hours (equivalent 

• 

to 1 year’s use) when shipped.
The settings can be changed to not display.

• 

When installing the unit in a dusty place, set the fi lter sign 

• 

display time to shorter intervals (1,250 hours).
Explain it to the customer that the fi lter needs to be cleaned 

• 

regularly to prevent clogging and also the time that is set.

Mode No.

FIRST CODE NO.

SECOND 

CODE NO.

01

02

10 (20)

0

Filter dirt

low

high

1 (low/high)

Displayed time

(units: hours)

2500/

1250

10000/

5000

3

Filter sign display

ON

OFF

INSTALLATION OF THE OPTIONAL AIR FILTER

10-4 

Purchase and install the air fi lter as in Table 6.

• 

Table 6

Air fi lter

12 · 18 type

FIL 36-42

24 · 30 · 36 · 42 · 48 · 54 type

FIL 48-61

Take off the part on the bottom of the front panel.

(1) 

Insert the air fi lter as far as it can go.

(2) 

Air filter (optional accessories)

INSTALLATION OF THE ELECTRIC HEATER KIT

10-5 

 WARNING

All phases of the electrical installation must comply with 

• 

national, state, provincial, and local codes.
When connecting an electric heater, be sure to install an 

• 

earth leakage circuit breaker procured locally.
If an earth leakage circuit breaker is not installed, electric 

• 

shock or fi re may result.
Regarding the rated current of the earth leakage circuit 

• 

breaker to be installed, refer to the H.M.C.A. value indicated 
on the manufacturer’s label or in a technical document.
The recommended rapid sensitive current and tripping time 

• 

are indicated below.

Recommended specifi cations of circuit breaker

Rapid sensitive current

30mA

Tripping time

0.1sec

Purchase and install the electric heater kit as in Table 7.

• 

Also refer to the installation and operating instructions that 

• 

come with the electric heater kit.
The indoor unit fan operates at H speed during HEATER 

• 

operation.

Table 7

Model

Electric heater kit model name

HKR-

03

HKR-

05C

HKR-

06

HKR-

08C

HKR-

10C

HKR-

15C

HKR-

20C

12 type

18 type

1

24 type

1

30 · 36 type

1

1

42 type

1

1

1

1

2

48 · 54 type

1

1

1

1

2

2

1

 : Auxiliary and Heat Pump Lockout: Electric heater opera-

tion with heat pump is allowed.

  : Heat Pump Lockout: Only electric heater operation is 

allowed. Heat pump and electric heater cannot operate at 
the same time.

2

 : Heat Pump Lockout: Only electric heater operation is al-

lowed. Heat pump and electric heater cannot operate at the 
same time. In addition, acceptable 2 step heating control.

Summary of Contents for FXTQ12PAVJU




















Reviews: