background image

3 User safety instructions

Installation and operation manual

6

FXSN50~112A2VEB

CO

 Conveni-Pack: indoor unit

4P602815-1C – 2020.05

(field supply), in order to be effective,
the unit must be electrically powered at
all times after installation, except for
short service periods.

CAUTION

Do NOT insert fingers, rods or other
objects into the air inlet or outlet. When
the fan is rotating at high speed, it will
cause injury.

CAUTION

▪ NEVER touch the internal parts of the

controller.

▪ Do NOT remove the front panel.

Some parts inside are dangerous to
touch and appliance problems may
happen. For checking and adjusting
the internal parts, contact your
dealer.

WARNING

This unit contains electrical and hot
parts.

WARNING

Before operating the unit, be sure the
installation has been carried out
correctly by an installer.

CAUTION

It is not good for your health to expose
your body to the air flow for a long
time.

CAUTION

To avoid oxygen deficiency, ventilate
the room sufficiently if equipment with
burner is used together with the
system.

CAUTION

Do NOT operate the system when
using a room fumigation-type
insecticide. Chemicals could collect in
the unit, and endanger the health of
people who are hypersensitive to
chemicals.

CAUTION

NEVER expose little children, plants or
animals directly to the airflow.

WARNING

Do NOT place objects below the indoor
and/or outdoor unit that may get wet.
Otherwise condensation on the main
unit or refrigerant pipes, air filter dirt or
drain blockage may cause dripping,
and objects under the unit may get
dirty or damaged.

WARNING

Do NOT place a flammable spray
bottle near the air conditioner and do
NOT use sprays near the unit. Doing
so may result in a fire.

Maintenance and service (see 

"7 Maintenance and

service" 

[

4

 9])

WARNING: 

 System contains

refrigerant under very high
pressure.

The system MUST be serviced by
qualified persons only.

CAUTION: Pay attention to the fan!

It is dangerous to inspect the unit while
the fan is running.

Be sure to turn off the main switch
before executing any maintenance
task.

WARNING

Never replace a fuse with a fuse of a
wrong ampere ratings or other wires
when a fuse blows out. Use of wire or
copper wire may cause the unit to
break down or cause a fire.

CAUTION

After a long use, check the unit stand
and fitting for damage. If damaged, the
unit may fall and result in injury.

CAUTION

Before accessing terminal devices,
make sure to interrupt all power supply.

Summary of Contents for FXSN112A2VEB

























Reviews: