background image

1-4

 Measure  and  mark  the  position  for  the  hanging  rod. 
Drill the hole for the angle nut on the ceiling and 

Þ

 x 

the hanging rod.
 The  installation  template  is  extended  according  to 
temperature  and  humidity.  Check  on  dimensions  in 
use.
 The dimensions of the installation template are the same 
as those of the ceiling opening dimensions.
 Before ceiling laminating work is covmpleted, be sure 
to 

Þ

 t the installation template to the indoor unit.

Con

Þ

 rm the pitch of the hanging rod.

 Hold the unit and hang it on the hanging rod with the 
nut and washer.
 Adjust the unit height to 35.0 mm between the indoor 
unit bottom surface and the ceiling surface.
 Con

Þ

 rm  with  a  level  gauge  that  the  unit  is  installed 

horizontally and tighten the nut and bolt to prevent unit 
failing and vibration.
 Open the ceiling board along the outer edge of the paper 
installation template.


 Drain pipe must be in downward gradient for smooth 
drainage.
 Avoid installing the drain pipe in up and down slope to 
prevent reversed water 

ß

 ow.

 During the drain pipe connection, be careful not to exert 
extra force on the drain connector at indoor unit.
 The  outside  diameter  of  the  drain  connection  at  the 

ß

 exible drain hose is 20 mm.

 Be sure to execute heat insulation (polyethylene foam 
with thickness more than 8.0 mm) on the drain piping to 
avoid the condensed water dripping inside the room.

Connect the main drain pipe to the 

ß

 exible drain.

 Feed water from 

ß

 exible drain hose to check the piping 

for leakage.
 When the test is completed, connect the 

ß

 exible drain 

hose to the drain connector on the indoor unit.


Indoor Unit

Ceiling
Board

35.0 mm

35.0 mm

Indoor Unit

Ceiling Board

Indoor Unit

Pipe Clamp

Good

Bad

Feed Water

Flexible Drain Hose

Main Drain Pipe

NOTE

This indoor unit uses a drain pump for condensed water drainage. Install the unit horizontally to prevent water leakage 
or condensation around the air outlet.

NOTE

  

Be sure to discuss the ceiling drilling work with the 

installers concerned.

Unit Hanging

Drain Pump Work

Drain Test

Unit Installation

15.0

538.0 

529.0

19.0

18.0

580.0 ~ 610.0 mm 

(Ceiling Board Opening)

32.0

38.0

505.0

448.0

88

.0

580.0 ~ 610.0 mm 

(Ceiling Board Opening)

Summary of Contents for FWF02CATNMV1

















Reviews: