background image

1-2

SAFETY PRECAUTIONS

INSTALLATION MANUAL

NOTICE

Disposal requirement

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed 
with unsorted household waste.
Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant, of oil 
and of other parts must be done by a quali

Þ

 ed installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this product 
is disposed of correctly, you will help to prevent potential negative consequences for the environment and human health. Please 
contact the installer or local authority for more information.
Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local and national 
legislation.

!

 WARNING

!

 CAUTION

Installation and maintenance should be performed by quali

Þ

 ed 

persons who are familiar with local code and regulation, and 
experienced with this type of appliance.
All 

Þ

 eld  wiring  must  be  installed  in  accordance  with  the 

national wiring regulation.
Ensure that the rated voltage of the unit corresponds to that of 
the name plate before commencing wiring work according to 
the wiring diagram.
The unit must be GROUNDED to prevent possible hazard due 
to insulation failure.
All electrical wiring must not touch the refrigerant piping, or 
any moving parts of the fan motors.
Con

Þ

 rm that the unit has been switched OFF before installing 

or servicing the unit.
Disconnect from the main power supply before servicing the 
air conditioner unit.
DO NOT pull out the power cord when the power is ON. This 
may cause serious electrical shocks which may result in 

Þ

 re 

hazards.
Keep  the  indoor  and  outdoor  units,  power  cable  and 
transmission  wiring,  at  least  1  m  from  TVs  and  radios,  to 
prevent distorted pictures and static. {Depending on the type 
and source of the electrical waves, static may be heard even 
when more than 1 m away}.

Please  take  note  of  the  following  important  points  when 
installing.

Do  not  install  the  unit  where  leakage  of 

ß

 ammable  gas 

may occur.
Ensure that drainage piping is connected properly.

 

 If  the  drainage  piping  is  not  connected  properly,  it 
may  cause  water  leakage  which  will  dampen  the 
furniture.

Ensure  that  the  unit’s  panel  is  closed  after  service  or 
installation.

 

 Unsecured  panels  will  cause  the  unit  to  operate 
noisily.

Sharp edges and coil surfaces are potential locations which 
may cause injury hazards.
Avoid from being in contact with these places.
Before  turning  off  the  power  supply,  set  the  remote 
controller’s  ON/OFF  switch  to  the  “OFF”  position  to 
prevent the nuisance tripping of the unit.

 If this is not done, 

the  unit’s  fans  will  start  turning  automatically  when  power 
resumes, posing a hazard to service personnel or the user.

Do not install the units at or near doorway.
Do not operate any heating apparatus too close to the air 
conditioner unit or use in room where mineral oil, oil vapour 
or  oil  steam  exist,  this  may  cause  plastic  part  to  melt  or 
deform as a result of excessive heat or chemical reaction.
When  the  unit  is  used  in  kitchen,  keep 

ß

 our  away  from 

going into suction of the unit.
This unit is not suitable for factory used where cutting oil 
mist or iron powder exist or voltage 

ß

 uctuates greatly.

Do not install the units at area like hot spring or oil re

Þ

 nery 

plant where sulphide gas exists.
Ensure  the  color  of  wires  of  the  outdoor  unit  and  the 
terminal markings are same to the indoors respectively.
IMPORTANT : DO NOT INSTALL OR USE THE AIR 
CONDITIONER UNIT IN A LAUNDRY ROOM.
Don't  use  joined  and  twisted  wires  for  incoming  power 
supply.
The  equipment  is  not  intended  for  use  in  a  potentially 
explosive atmosphere.


This manual provides the procedures of installation to ensure a safe and good standard of operation for the air conditioner unit.
Special adjustment may be necessary to suit local requirement.
Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.
This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for commercial use by 
lay persons.
This appliance is not intended for use by persons, including children, with reduced physical, sensory or mental capabilities, or lack 
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person 
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.

Summary of Contents for FWF02CATNMV1

















Reviews: