background image

English

14

Indoor Unit Installation (2)

11.

When connecting to an HA system

1) Remove the electric box. (See 

3. How to set the 

different addresses

 on page 4.) 

2) Cut off the pins using a nipper.
3) Wire as shown in the diagram and connect the 

connection cord to the S21 connector.

4) Attach the side metal plate cover and thermistor 

sensor and return the electric box to its previous 
state.

5) Attach connectors 5P, 6P, and 7P. 
6) Replace the front metal plate cover and the sensor 

securing plate.

Half concealed installation

Only items peculiar to this installation method are given here. See 

Exposed Installation

 for additional instructions.

1.

Wall hole

• Drill a wall hole of the size shown in the illustration on the right.

2.

Installation of supplemental plate for attaching main unit

• The rear of the unit can be fixed with screws at the points shown in the illustration as below. Be sure to install the 

supplemental plate in accordance with the depth of the inner wall.

 CAUTION

1) The supplemental plate for installing the main unit must be used, or there will be a gap between the unit and the wall.

S21

HA cord

Side metal plate cover

HA connector 
(S21)

2) Pin

Front metal plate cover

Sensor 
securing 
plate

670-690

585-595

(Unit: mm)

Open size

Opening hole

Floor

Fixing point
on the back

Supplemental plate 
(Field supply)

140

230

644

Screw hole

Screw hole

Opening hole

150

250

95

Supplemental plate 
(Field supply)

250

200

(Unit: mm)

3PEN477070-1A.book  Page 14  Tuesday, March 28, 2017  10:01 AM

Summary of Contents for FVXM35FV1B

























Reviews: