background image

32

Care

When the Need Arises

14

FAQ

Indoor unit

Outdoor unit

The flaps do not start swinging 

 

 immediately.

•   The air conditioner is adjusting the position of the flaps. 

The flaps will start moving soon.

Different sounds are heard.

 

„

  A sound like flowing water

•    This sound is generated because the refrigerant in 

the air conditioner is flowing.

•    This is a pumping sound of the water in the air 

conditioner and can be heard when the water is 
pumped out from the air conditioner during COOL or 
DRY operation.

 

„

Blowing sound

•  This sound is generated when the flow of the 

refrigerant in the air conditioner is switched over.

 

„

  Ticking  sound

•    This sound is generated when the cabinet and 

frame of the air conditioner slightly expand or shrink 
as a result of temperature changes.

 

„

Whistling sound

•  This sound is generated when refrigerant flows 

during defrosting operation.

 

„

 Clicking sound during operation or idle time

•    This sound is generated when the refrigerant control 

valves or the electrical parts operate.

 

„

 Clopping  sound

• 

  

This sound is heard from the inside of the air conditioner 
when the exhaust fan is activated while the room doors 
are closed. Open the window or turn off the exhaust fan.

The outdoor unit emits water or steam.

 

„

 In HEAT operation

•  The frost on the outdoor unit melts into water or steam when the air 

conditioner is in defrosting operation.

 

„

In COOL or DRY operation 

•   Moisture in the air condenses into water on the cool surface of the outdoor 

unit piping and drips.

Operation does not start soon.

 

„

  When 

 was pressed soon after operation 

was stopped.

 

„

  When the mode was reselected.

•   This is to protect the air conditioner.

 

You should wait for about 3 minutes.

HEAT operation stops suddenly and 

a flowing sound is heard.

•   The outdoor unit is defrosting. HEAT operation starts 

after the frost on the outdoor unit has been removed.

 

This can take about 4 to 12 minutes.

The air conditioner stops generating 

airflow during HEAT operation.

•   Once the set temperature is reached, the airflow rate is 

reduced and operation stopped in order to avoid 
generating a cool airflow. Operation will resume 
automatically when the indoor temperature falls.

01_EN_3P552666-9C.indd   32

29-Apr-19   8:44:14 AM

Summary of Contents for FTXV50UVMA









































Reviews: