background image

3

English

Installation Tips

1.

Removing and installing front panel.

• Removal method

1) Place your fingers in the indentations on the main unit (one each on the 

left and right sides), and open the panel until it stops.

2) Continue to open the front panel further while sliding the panel to the right 

and pulling it toward you in order to disengage the rotating shaft on the 
left side. To disengage the rotating shaft on the right side, slide the panel 
to the left while pulling it toward you.

• Installation method

Align the tabs of the front panel with the grooves, and push all the way in. Then 
close slowly. Push the center of the lower surface of the panel firmly to engage the 
tabs.

2.

Removing and installing front grille.

• Removal method

1) Remove front panel to remove the air filter.
2) Remove the screws (2) from the front grille.
3) In front of the 

{{{

 mark of the front grille, there are 3 upper hooks. 

Lightly pull the front grille toward you with one hand, and push down on 
the hooks with the fingers of your other hand.

When there is no work space because the unit is close to ceiling

CAUTION

Be sure to wear protection gloves.

Place both hands under the center of the front grille, and while pushing up, pull it toward you.

• Installation method

1) Install the front grille and firmly engage the upper hooks (3 locations).
2) Install 2screws of the front grille.
3) Install the air filter and then mount the front panel.

3.

How to set the different addresses.

When two indoor units are installed in one room, the two wireless remote controllers 
can be set for different addresses.
1) In the same way as when connecting to an HA system, remove the metal plate 

electrical wiring cover.

2) Cut the address jumper (JA) on the printed circuit board.
3) Cut the address jumper (J4) in the remote controller.

Indentations on 
the main unit

Push the rotating 
shaft of the front 
panel into the groove.

Rotating shaft

¡¡¡ mark area

(3 locations)

Upper hook

Lightly pull the front 
grille toward you with 
one hand, and push 
down on the hooks with 
the fingers of your other 
hand. (3 locations)

Push
down.

Upper hook

Upper hook

1) Push up.

2) Pull toward you.

ADDRESS

EXIST
 CUT

1
2

JA

JA

ADDRESS

J4

EXIST
 CUT

1
2

J4

01_EN_3P207973-1D.fm  Page 3  Friday, September 4, 2009  10:44 AM

Summary of Contents for FTX20GV1B
















Reviews: