background image

 

FCQ35~14 FCQH71~140C7VEB
Split System air conditioners
4PW31577-1B

Installation manual

6

-

Confirm the drain operation looking at the drain socket.

-

After checking the drainage flow, turn off power, remove
the control box lid and disconnect the single phase power
supply from the inter unit wiring terminal block again.
Attach the control box lid as before.

E

LECTRIC

 

WIRING

 

WORK

General instructions

All field supplied parts and materials and electric works must
conform to local codes.

Use copper wire only.

Follow the 'Wiring diagram' attached to the unit body to wire the
outdoor unit, indoor units and the remote controller. For details
on hooking up the remote controller, refer to the "Installation
manual of the remote controller".

All wiring must be performed by an authorized electrician.

A main switch or other means for disconnection, having a
contact separation in all poles, must be incorporated in the fixed
wiring in accordance with relevant local and national legislation.
Note that the operation will restart automatically if the main
power supply is turned off and then turned back on again.

Refer to the installation manual attached to the outdoor unit for
the size of power supply electric wire connected to the outdoor
unit, the capacity of the earth leakage circuit breaker and fuse,
and wiring instructions.

Be sure to ground the air conditioner.

Do not connect the ground wire to:
-

gas pipes: might cause explosions or fire if gas leaks.

-

telephone ground wires or lightning rods: might cause 
abnormally high electric potential in the ground during 
lightning storms.

-

plumbing pipes: no grounding effect if hard vinyl piping is 
used.

Electrical characteristics

Specifications for field wire

W

IRING

 

EXAMPLE

 

AND

 

HOW

 

TO

 

SET

 

THE

 

REMOTE

 

CONTROLLER

How to connect wiring 

(See figure 10)

Inter unit wiring
Remove the control box lid (1) and connect the inter unit wiring
terminal block inside with the matching numbers and connect
the ground wire to the grounding terminal. While doing this, pull
the wires inside through the hole in the casing and clamp the
wires along with other wires using a clamp as indicated in the
figure.

Remote controller wiring
Remove the control box lid (1) and pull the wires inside through
the hole in the casing and connect to the remote controller
wiring terminal block. Securely fix the wiring using a clamp as
indicated in the figure.

After connection
Attach the small sealing (supplied with the unit) around the
cables to prevent infiltrating of water from the outside into the
unit. If two or more cables are used, divide the small sealing into
the required number of pieces and wrap them around all the
cables.

Attach the control box lid

Precautions

1

Observe the notes mentioned below when wiring to the power
supply terminal board.

-

Use a round crimp-style terminal for insulation sleeve for 
connection to the terminal block for wiring the units. When 
none are available, follow the instructions below.

-

Do not connect wires of different gauge to the same power 
supply terminal. (Looseness in the connection may cause 
overheating.)

-

When clamping wiring, use the clamps (delivered with the 
unit) to prevent outside pressure being exerted on the wiring 
connections. Tie up firmly. When doing the wiring, make sure 
the wiring is neat and does not cause the control box to stick 
up. Close the cover firmly.

1

Control box lid

2

Inter unit wiring

3

Earth cable

4

Inter unit wiring terminal block

5

Clamp

6

Transmission wiring

7

Terminal board for transmission wiring

8

Opening for cables

9

Wiring diagram label
(on the back side of the control box lid)

10

Remote controller wiring

Inter unit wiring terminal block (4) 

NOTE

For details, refer to "Electrical data".

1

2

Wire

Size (mm

2

)

Length

Between 

indoor units

H05VV-U4G

(1),(2)

(1) Shows only in case of protected pipes. Use H07RN-F in case of no protection.
(2) Run transmission wiring between the indoor and outdoor units through a conduit 

to protect against external forces, and feed the conduit through the wall together 
with refrigerant piping.

2,5

Unit-Remote 

controller

Sheathed wire 

(2 wire)

(3)

(3) Use double insulation wire for remote controller (sheath thickness: 

1 mm) or run 

wires through a wall or conduit so that the user cannot come in contact with them.

0.75-1.25

500 m

(4)

(4) This length is the total maximum extended length in the system in case of group 

control.

1

Control box lid

2

Inter unit wiring

3

Earth cable

4

Inter unit wiring terminal block

5

Clamp (field supply)

6

Remote controller wiring

7

Remote controller wiring terminal block

8

Opening for cables

9

Wiring diagram label (on the back side of the control box lid)

1

2

3

1

Round crimp-style terminal

2

Attach insulation sleeve

3

Wiring

Downloaded from AC-Manual.com Manuals

Summary of Contents for FCQ35C7VEB x 3

















Reviews: