background image

English

19

CAUTION

After all the wiring connections are done, fill in any gaps in the through holes with putty or insulation

 (procured locally) to prevent small animals and insects from entering the unit from outside. (If any do get in, 

they

 

could cause short circuits in the control box.)

(5) Mount the provided wire fixing bracket (12) with 

the wire fixing screw (13). Fix each wire with the 
provided clamp (8). 

Precautions to be taken for power supply wiring

Use a round crimp-style terminal for connection to the 
power supply terminal block.

In case it cannot be used due to unavoidable reasons, be sure to observe the following instructions.

(Loose wiring and similar problems may result in abnormal heat build-up.)

In wiring, make certain that prescribed wires are used, carry out complete connections, and fix the wires so 
that external forces are not applied to the terminals.

If the strand wire is used, do not solder it.

Tightening torque for the terminal screws.

Use the correct screwdriver for tightening the terminal screws. If the blade of screwdriver is too small, the 
head of the screw might be damaged, and the screw will not be properly tightened.

If the terminal screws are tightened too hard, screws might be damaged.

Refer to the table below for the tightening torque of the terminal screws.

Tightening torque (N·m)

6

9

.

0

 

o

0

8

.

0

r

e

ll

o

r

t

n

o

c

 

e

t

o

m

e

r

 

r

o

k

c

o

l

b

 l

a

n

i

m

r

e

T

4

4

.

1

 

o

8

1

.

1

s

ti

n

u

 

e

h

g

n

ir

i

w

 

r

o

k

c

o

l

b

 l

a

n

i

m

r

e

T

4

4

.

1

 

o

8

1

.

1

l

a

n

i

m

r

e

h

t

r

a

E

Wiring the units
Power supply wiring
Ground wiring

 

Remote controller 
wiring

Fixing use

Wire fixing screw (13) (accessory)

Wire fixing bracket (12) (accessory)

Clamp (8) (accessory)

Electric wire

Round crimp-style terminal

Attach insulation sleeve

Good

Wrong

Wrong

Connect wires of the 
same gauge to both 
side. (GOOD)

Do not connect wires 
of the same gauge to 
one side. (WRONG)

Do not connect wires 
of different gauges. 
(WRONG)

01_EN_3PN06583-10W.fm  Page 18  

Thursday, March 24, 2011  9:03 AM

Summary of Contents for FBQ20DAVMK





























































Reviews: