Daikin DC96SN Service Instructions Manual Download

Page: 44 / 63

1 STAGE TROUBLESHOOTING CODES

Symptom

LED

Status

Fault Description

Corrective Actions

Flame sense micro amp signal is minimal

Flame sensor is coated/oxidized

Flame sensor incorrectly positioned in burner

fame

Compare current gas pressure to rating plate and adjust

as needed

Problem with igniter circuit

Check and correct wiring from integrated control module to

igniter

Improperly connected or shorted igniter

Poor unit ground

Igniter relay fault on integrated control module

Check igniter output from control, replace if necessary

Polarity of 115 volt AC is reversed

Correct polarity, check and correct wiring if necessary

Poor unit ground

Verify proper ground, correct if necessary

Gas valve is not energized when it should be

Check wiring in gas valve circuit

External Gas Valve Error

Replace integrated control board

Gas valve is energized when it should not be

Check wiring in gas valve circuit

Internal gas valve error

Replace integrated control board

Furnace fails to operate.

No 115 power to furnace or no 24 volt power

to integrated control module.

Restore high voltage power to furnace and integrated

control module.

Blown fuse or tripped circuit breaker

Correct condition which caused fuse to open, replace fuse

Integrated control module is non- functional

Replace non-functional integrated control module.

Furnace fails to operate



Grounding fault

Poor neutral connection

Verify neutral wire connection to furnace & continuity to

ground source

Furnace fails to operate



Open roll out switch

Check for correct gas pressure Check for correct burner

alignment

Check for and correct burner restriction

Furnace fails to operate



Ignitor Open

Check for Ignitor wiring.

Replace Damaged Ignitor

Furnace fails to operate



Inducer relay Error

Replace integrated control board

Twinning feature not working



TWIN Error

Check for wiring connections.

Replace integrated control board

Furnace fails to operate



Internal Faults or IRQ Loss in Control Board

Replace integrated control board

TROUBLESHOOTING CHART

Furnace fails to operate



Diagnose and replace shorted igniter as needed Verify and

correct unit ground wiring if needed

Normal furnace operation



Clean flame sensor if coated or oxidized Inspect for proper

flame sensor alignment

Lazy burner flame due to improper gas

pressure or combustion air

Furnace fails to operate



None

Integrated control module

LED display provides no

signal

Furnace fails to operate



Furnace fails to operate



Summary of Contents for DC96SN
































































Search results

Summary of Contents for DC96SN

Reviews:

Related manuals for DC96SN

Brands by name

Popular brands

Daikin DC96SN, Service Instructions Manual

Search results

Summary of Contents for DC96SN

Reviews:

Related manuals for DC96SN

Brands by name

Popular brands